Chassis Suspension & Motorsport Anti-Roll Bars, Hollow Torsion-Bar d^4 Scaling
Hollow Torsion-Bar Spring Rate, Twist & Shear Formula
Calculate Polar Area Moment J (cm⁴), Torsional Angular Stiffness k_theta (N·m/deg), Suspension Windup Twist Angle (deg), and Outer-Surface Shear Stress tau_max (MPa).
Gun-drilling a 50% ID bore down a 32 mm torsion bar cuts unsprung steel mass by 25%—while losing ONLY 6.25% (0.5^4) of torsional spring rate
Automotive Suspension Torsion Bars and Tubular Motorsport Anti-Roll (Sway) Bars (Outer Diameter d_o mm, Inner Bore d_i mm, Active Effective Length L mm, Shear Modulus G = 78.5 GPa for shot-peened 5160 / 300M spring steel) exploit **Fourth-Power Polar Moment of Area J = (pi / 32) * (d_o^4 - d_i^4) (mm⁴, / 10,000 for cm⁴). Because core steel near the neutral axis carries almost zero shear strain (tau(r) ~ r), boring out d_i / d_o = 0.50 removes (0.50)^2 = 25.0% of dead weight while subtracting just (0.50)^4 = 6.25% of Angular Spring Rate ktheta = (((G * 1,000) * J) / L) * (pi / 180) / 1,000 (N·m/deg). Under Control-Arm Bump Torque T (N·m), Windup Twist Angle equals theta = T / ktheta (deg) and Outer-Fiber Maximum Torsional Shear Stress equals taumax = (16,000 * T * d_o) / (pi * (d_o^4 - d_i^4))** (MPa).
Verify on a 32 mm OD x 16 mm ID (6 mm wall) Motorsport Tubular Anti-Roll / Torsion Bar—Outer_Diameter d_o = 32.0 mm (B2), Inner_Bore d_i = 16.0 mm (B3), Active_Length L = 1,050 mm (B4), Steel_Shear_Modulus G = 78.5 GPa (B5), and Full-Bump_Arm_Torque T = 1,850 N·m (B6): Polar Moment J equals 9.651 cm⁴ (E2), Torsional Spring Rate ktheta equals 125.93 N·m/deg (E3), Windup Angle equals 14.69° (E4), and Outer-Surface Shear Stress equals 306.7 MPa (E5).
| Hollow vs Solid Torsion-Bar KPI (do=32 mm, L=1,050 mm, G=78.5 GPa, T=1,850 N·m) | Formula | Verified Output |
|---|---|---|
| Polar Moment of Area J (cm⁴) | ((PI() / 32) * (do_mm^4 - di_mm^4)) / 10000 | 9.651 cm⁴ hollow (10.294 cm⁴ solid) |
| Torsional Stiffness (N·m/deg) | (((G_GPa*1000 * J_mm4) / L_mm) * PI/180) / 1000 | 125.93 N·m/deg (134.33 solid = +6.7%) |
| Windup Twist Deflection (deg) | Applied_Torque_Nm / Stiffness_Nm_deg | 14.69° hollow (13.77° solid) |
| Outer-Surface Shear Stress (MPa) | (16000 * T_Nm * do_mm) / (PI * (do^4 - di^4)) | 306.7 MPa hollow (287.5 MPa solid) |
Saint-Venant / Coulomb Hollow-Shaft Torsional Stiffness & Shear Formula
Validate Outer_Diameter d_o in [8, 150] mm, Inner_Bore d_i in [0, 0.85 * d_o) (0 = solid bar), Active_Length L in [100, 4,000] mm, Shear_Modulus G in [20, 100] GPa (~26 Al, ~44 Ti, ~78.5 steel), and Torque T > 0 N·m.
=LET(do_m, B2, di_m, B3, lb_m, B4, gs_g, B5, tq_n, B6, IF(OR(do_m < 8, do_m > 150, di_m < 0, di_m >= 0.85 * do_m, lb_m < 100, lb_m > 4000, gs_g < 20, gs_g > 100, tq_n <= 0), "Invalid Torsion Input", ROUND((16000 * tq_n * do_m) / (PI() * ((do_m ^ 4) - (di_m ^ 4))), 1)))Solid-Bar Comparison (d_i = 0 mm) 25%-Mass-for-6.25%-Stiffness Proof Check
Set B3 = 0 mm to compare an identical 32 mm solid bar (33% heavier than the hollow tube): Polar Moment E2 nudges up from 9.651 to 10.294 cm⁴, Stiffness E3 rises just +6.67% to 134.33 N·m/deg (13.77° twist in E4), and Peak Surface Shear E5 drops only 6.25% from 306.7 to 287.5 MPa—confirming why GT race cars and aircraft landing struts always run hollow torsion tubes.
=IF(ISTEXT(E5), E5, LET(jm_q, (PI() / 32) * ((B2 ^ 4) - (B3 ^ 4)), ROUND((((B5 * 1000) * jm_q) / B4) * (PI() / 180) / 1000, 2)))Try the example
Use the original values or change them to test your understanding.