Arte SheetsLearn. Try. Understand.

Geotechnical Excavation Support, USACE Cantilever Steel Sheet-Pile Wall Mechanics

Cantilever Sheet-Pile Zero-Pressure Depth & Moment Formula

Calculate Rankine Active Ka & Passive Kp Earth Coefficients, Zero-Net-Pressure Depth z0 Below Dredge Line (m), and Active Wedge Overturning Moment at z0 (kN·m/m).

Below the excavation dredge line, active earth pressure does NOT vanish—passive resistance has to out-climb gamma*Ka*(H + z) first

An unanchored Cantilever Steel Sheet-Pile Wall retaining granular cut height H (m, Unit Weight gamma kN/m³, Friction Angle phi deg) derives its entire stability from passive soil resistance mobilized in front of the driven toe. Above the excavation dredge line, active pressure climbs linearly to sigmaa,dredge = gamma * K_a * H, where K_a = (1 - SIN(phi)) / (1 + SIN(phi)). Below depth z under the dredge line, front-side passive resistance gamma * K_p * z (K_p = (1 + SIN(phi)) / (1 - SIN(phi)) = 1 / K_a) opposes continuing active pressure gamma * K_a * (H + z), crossing **Zero Net Lateral Pressure at Pivot Depth z_0 = (K_a * H) / (K_p - K_a)** (m). Integrating the dual-triangle active diagram from 0 down to z_0 yields Exact Active Thrust R_a = 0.5 * gamma * K_a * H * (H + z_0) (kN/m) acting at centroid (H + 2 * z_0) / 3 above z_0—driving **Pivot Overturning Moment Mz0 = R_a * ((H + 2 * z_0) / 3)** (kN·m/m, the governing bending demand used to select Z-profile section modulus S_x).

Verify on a 4.20 m Temporary Granular Excavation Cutoff—Retained_Cut_Height H = 4.20 m (B2), Compact_Sand_Unit_Weight gamma = 18.5 kN/m³ (B3), and Drained_Friction_Angle phi = 32.0° (B4): Rankine K_a equals 0.307 (E2), K_p equals 3.255 (E3), Zero-Net-Pressure Depth z_0 sits 0.438 m below dredge level (E4), and Active Overturning Moment at z_0 reaches 93.7 kN·m/m (E5).

USACE Cantilever Sheet-Pile KPI (H=4.20 m, gamma=18.5 kN/m³, phi=32° vs 25°)FormulaVerified Output
Rankine Active Coefficient Ka(1 - SIN(phi_rad)) / (1 + SIN(phi_rad))0.307 (0.406 @ loose sand 25°)
Rankine Passive Coefficient Kp(1 + SIN(phi_rad)) / (1 - SIN(phi_rad))3.255 (2.464 @ loose sand 25°)
Zero-Net-Pressure Depth z0 (m)(Ka * Cut_Height_H) / (Kp - Ka)0.438 m (0.828 m deeper @ 25°)
Overturning Moment at z0 (kN·m/m)(0.5*gamma*Ka*H*(H+z0)) * ((H+2*z0)/3)93.7 kN·m/m (154.8 kN·m/m = +65% jump)

Rankine Active-Passive Pressure Crossover Depth z0 & Bending Moment Formula

Validate Cut_Height H in [0.5, 12.0] m, Unit_Weight gamma in [13.0, 24.0] kN/m³, and granular Friction_Angle phi in [18°, 45°].

=LET(hc_m, B2, gm_k, B3, ph_r, B4 * (PI() / 180), ka_c, (1 - SIN(ph_r)) / (1 + SIN(ph_r)), kp_c, (1 + SIN(ph_r)) / (1 - SIN(ph_r)), zz_m, (ka_c * hc_m) / (kp_c - ka_c), ra_k, 0.5 * gm_k * ka_c * hc_m * (hc_m + zz_m), IF(OR(hc_m < 0.5, hc_m > 12, gm_k < 13, gm_k > 24, B4 < 18, B4 > 45), "Invalid Sheet-Pile Input", ROUND(ra_k * ((hc_m + 2 * zz_m) / 3), 1)))

Loose Silty Sand (phi = 25°) +65% Bending-Moment Escalation Check (Set Friction Angle B4 = 25°)

Encounter looser phi B4 = 25° sand at the toe: K_a E2 rises to 0.406 while K_p E3 drops to 2.464, nearly DOUBLING Zero-Pressure Depth z_0 E4 to 0.828 m and driving Bending Moment E5 up +65% to 154.8 kN·m/m—requiring a heavier AZ-series sheet-pile section or tieback waler.

=IF(ISTEXT(E5), E5, LET(ph_r, B4 * (PI() / 180), ka_c, (1 - SIN(ph_r)) / (1 + SIN(ph_r)), kp_c, (1 + SIN(ph_r)) / (1 - SIN(ph_r)), ROUND((ka_c * B2) / (kp_c - ka_c), 3)))

Try the example

Use the original values or change them to test your understanding.

Further reading