Arte SheetsLearn. Try. Understand.

Closed-Die Impression Forging, Automotive Crankshaft/Connecting-Rod Tooling & Flash Design

Closed-Die Forging Flash-Land Factor & Tonnage Formula

Calculate Flash-Land Width-to-Thickness Aspect Ratio w/t, Cavity Multiplying Factor Kf = 3.0 + 1.15*(w/t), Mean Cavity Die Pressure (MPa), and Required Mechanical Press Capacity (metric tons).

In closed-die impression forging, squeezing thin cooling flash across the narrow flash land—not filling the main cavity—dictates peak press tonnage

To guarantee hot steel fills deep rib and boss corners inside a closed-die impression, toolmakers deliberately machine a narrow perimeter Flash Land of width w (mm) and gap thickness t (mm) leading into a relief flash gutter. At bottom dead center, that thin ribbon of flash chills rapidly AND faces extreme w / t friction-hill extrusion resistance, acting as a high-pressure hydraulic choke that pressurizes the entire Projected Part + Flash Plan Area A_total = (A_part + A_flash) * 100 (mm²). Industrial forging shop design models Cavity Multiplying Factor K_f = 3.0 + 1.15 * (w / t) (~6 for simple chunky shapes with thick flash up to 10–12+ for intricate connecting rods with thin w/t = 6–8 flash lands), giving Mean Cavity Pressure P_avg = K_f * Y_f (MPa) and Press Rating Tonnage_t = (P_avg * A_total) / (9.80665 * 1,000) metric tons.

Verify on a Forged Steel Automotive Connecting Rod—Projected_Part_Area A_p = 140.0 cm² (B2), Perimeter_Flash_Land_Area A_f = 45.0 cm² (A_total = 18,500 mm², B3), Finish-Blow_Flow_Stress Y_f = 180.0 MPa (B4), Flash_Land_Width w = 12.0 mm (B5), and Flash_Gap_Thickness t = 2.40 mm (B6 -> w / t = 5.00 in E2): Multiplying Factor K_f equals 8.75 (E3), Mean Die Cavity Pressure hits 1,575.0 MPa (E4), requiring a 2,971.2 metric-ton (~3,000-ton) mechanical forging press (E5).

Closed-Die Impression KPI (Ap=140 + Af=45 cm², Yf=180 MPa, Flash w=12, t=2.4 mm)FormulaVerified Output
Flash-Land Aspect Ratio (w / t)Flash_Land_Width_w / Flash_Thick_t5.00 (8.00 @ over-coined 1.5 mm flash)
Cavity Multiplying Factor Kf3.0 + 1.15 * (w_mm / t_mm)8.75 (12.20 @ 1.5 mm thin flash)
Mean Die Cavity Pressure (MPa)Kf * Finish_Flow_Stress_Yf_MPa1,575.0 MPa (2,196.0 MPa risks die crack)
Required Press Capacity (t)(P_avg_MPa * Total_Area_mm2) / 9806.652,971.2 t (4,142.7 t stalls 3,500t press)

Flash-Land Aspect Choke Factor Kf & Impression-Forging Press Tonnage Formula

Validate Part_Area > 0 cm², Flash_Area >= 0 cm², Flow_Stress > 0 MPa, Flash_Width w > 0 mm, and Flash_Thickness t > 0 mm with 1 <= w / t <= 12.

=LET(ap_c, B2, af_c, B3, yf_m, B4, fw_m, B5, ft_m, B6, IF(OR(ap_c <= 0, af_c < 0, yf_m <= 0, fw_m <= 0, ft_m <= 0, (fw_m / ft_m) < 1, (fw_m / ft_m) > 12), "Invalid Die Input", LET(wt_r, fw_m / ft_m, kf_m, 3 + 1.15 * wt_r, pm_a, kf_m * yf_m, ROUND((pm_a * ((ap_c + af_c) * 100)) / 9806.65, 1))))

Thin 1.50 mm Over-Closed Flash-Gap Press-Stall Check (Set Flash Thickness t B6 = 1.50 mm)

Close the dies too tightly so Flash Gap t B6 shrinks from 2.40 mm down to 1.50 mm (w / t = 8.00 in E2): Multiplying Factor K_f E3 jumps to 12.20, Mean Cavity Stress E4 spikes to 2,196.0 MPa (exceeding H13 hot-work tool-steel fatigue limits), and Press Tonnage E5 surges +39.4% to 4,142.7 metric tons—locking a 3,500-ton crank press at bottom dead center.

=IF(ISTEXT(E5), E5, ROUND((3 + 1.15 * (B5 / B6)) * B4, 1))

Try the example

Use the original values or change them to test your understanding.

Further reading