Arte SheetsLearn. Try. Understand.

Automotive Transmission Gear Manufacturing, CNC Cylindrical Gear Hobbing Kinematics

CNC Gear Hobbing Sync RPM, Feed & Cycle Time Formula

Calculate Hob Cutter Spindle Speed (RPM), Electronic-Gearbox Synchronized Worktable Speed (RPM), Axial Saddle Feed Rate (mm/min), and Hobbing Cut Time per Stack (min).

Switching from a 2-start TiAlN carbide/PM-HSS roughing hob to a 1-start finishing hob on a 96-tooth gear slows worktable rotation 5.7x—stretching cycle time from 1.37 to 12.47 minutes

Continuous Generating Gear Hobbing meshes a worm-shaped fluted Hob Cutter (Outside Diameter d_h mm, Thread Starts z_0 = 1..4) spinning at **N_h = (1,000 * V_c) / (pi * d_h) (RPM for Surface Cutting Speed V_c m/min) with a CNC direct-drive Worktable (Gear Tooth Count z_2) locked electronically to the exact kinematic Worm-Wheel Indexing Ratio N_w = N_h * (z_0 / z_2) (RPM). Because involute generating facets form once per full worktable revolution, Axial Saddle Feed f_a (mm/work-rev) advances down the gear blank at v_f = N_w * f_a (mm/min), machining Total Approach + Face Stroke Ltot = b + Lapproach (mm) in t_m = Ltot / v_f** (minutes).

Verify on a 48-Tooth EV Reduction Helical Gear Cut Dry with a 2-Start Coated Hob—Hob_Diameter d_h = 95.0 mm (B2), Cutting_Speed V_c = 135 m/min (B3), Hob_Starts z_0 = 2 (B4), Gear_Teeth z_2 = 48 (B5), Axial_Feed f_a = 2.40 mm/work-rev (B6), and Total_Stroke Ltot = 62.0 mm (B7): Hob Spindle Speed equals 452.3 RPM (E2), Synchronized Worktable Speed equals 18.85 RPM (E3), Axial Feed Velocity equals 45.23 mm/min (E4), finishing the gear in just 1.371 minutes (82.3 seconds. E5).

CNC Generating Gear Hobbing KPI (Hob dh=95 mm, Total Stroke=62 mm)FormulaVerified Output
Hob Spindle Speed Nh (RPM)(1000 * Cutting_Vc_m_min) / (PI() * dh_mm)452.3 RPM (318.3 RPM wet HSS)
Synchronized Table Speed Nw (RPM)Hob_Spindle_Nh_RPM * (Starts_z0 / Teeth_z2)18.85 RPM (3.32 RPM @ 1-start / 96T)
Axial Saddle Velocity vf (mm/min)Worktable_Nw_RPM * Axial_Feed_fa_mm_rev45.23 mm/min (4.97 mm/min fine finish)
Generating Cut Time tm (min)Total_Stroke_Ltot_mm / Axial_Vel_vf_mm_min1.371 min (12.466 min = 9.1x slower)

Electronic-Gearbox Generating Hobbing Indexing & Cycle-Time Formula

Validate Hob_Diameter d_h in [20, 400] mm, Cutting_Speed V_c in [15, 450] m/min, Hob_Starts z_0 in [1, 6], Gear_Teeth z_2 in [6, 500], Axial_Feed f_a in [0.2, 12.0] mm/rev, and Total_Stroke Ltot in [5, 1,000] mm.

=LET(dh_m, B2, vc_m, B3, zs_h, B4, zg_t, B5, fa_m, B6, lt_m, B7, nh_r, (1000 * vc_m) / (PI() * dh_m), vf_m, (nh_r * (zs_h / zg_t)) * fa_m, IF(OR(dh_m < 20, dh_m > 400, vc_m < 15, vc_m > 450, zs_h < 1, zs_h > 6, zg_t < 6, zg_t > 500, fa_m < 0.2, fa_m > 12, lt_m < 5, lt_m > 1000), "Invalid Hobbing Input", ROUND(lt_m / vf_m, 3)))

Single-Start AGMA Class-10 Finish Hob on 96-Tooth Ring (V_c = 95, z_0 = 1, f_a = 1.5) Check

Switch to a single-start (B4 = 1) precision hob at B3 = 95 m/min and B6 = 1.50 mm/rev to cut a B5 = 96-tooth ring gear without lead-crown feed marks: Worktable Speed E3 drops to 3.32 RPM (4.97 mm/min saddle feed in E4), multiplying Cutting Time E5 9.1-fold to 12.466 minutes.

=IF(ISTEXT(E5), E5, LET(nh_r, (1000 * B3) / (PI() * B2), ROUND(nh_r * (B4 / B5), 2)))

Try the example

Use the original values or change them to test your understanding.

Further reading