Arte SheetsLearn. Try. Understand.

Aerospace LH2/LN2 Storage & MRI Cryostats, Multi-Layer Superinsulation (MLI) Boil-Off

Cryogenic Dewar MLI Heat Leak & NER Boil-Off Formula

Calculate MLI Blanket Radiative/Conductive Shell Leak (W), Total Parasitic Heat Load Including Neck/Supports (W), Daily Boil-Off Mass (kg/d), and Normal Evaporation Rate NER (%/d).

A micro-pinhole degrading Dewar vacuum from 10⁻⁴ to 0.1 mbar ruins MLI superinsulation 149x—jumping LN2 boil-off from 3.57 kg/day (0.085%) to 352 kg/day and lifting relief valves

Vacuum-Jacketed Cryogenic Dewars storing LN_2 (77.4 K, hfg = 199.1 kJ/kg), LOX (90.2 K), LH_2 (20.3 K), or LHe (4.2 K) wrap 30–60 layers of double-aluminized Mylar + glass-veil spacer inside a < 10⁻⁴ mbar high-vacuum annulus to achieve Apparent MLI Thermal Conductivity keff ~= 0.04–0.08 mW/(m·K) (500x better than stagnant air). Across Inner Vessel Area A (m²), Blanket Thickness t (mm), Warm Wall T_h (K), and Boiling Cryogen T_c (K), **Shell Heat Leak QMLI = ((keff / 1,000) * A * (T_h - T_c)) / (t / 1,000) (W) combines with G-10 fiberglass support straps and stainless fill/vent neck conduction Qneck (W) to evaporate mboil = ((QMLI + Qneck) * 86.4) / hfg (kg/day), rated commercially as Normal Evaporation Rate NER = (mboil / Mstored) * 100%** (%/day).

Verify on a 5,200-Liter (4,200 kg LN_2) Bulk Hospital Cryogenic Vessel—Inner_Vessel_Area A = 14.5 m² (B2), MLI_Blanket_Thickness t = 32.0 mm (B3), High-Vacuum_keff = 0.055 mW/(m·K) (B4), Ambient_Shell T_h = 295 K (B5), Boiling_LN_2 T_c = 77.4 K (B6), Support_&_Piping_Leak Qneck = 2.80 W (B7), Latent_Heat hfg = 199.1 kJ/kg (B8), and Stored_LN_2_Inventory M = 4,200 kg (B9): MLI Blanket Heat Leak equals just 5.42 W (E2), Total Parasitic Heat Load equals 8.22 W (E3), Daily Boil-Off Mass equals 3.57 kg/d (E4), achieving 0.085%/day NER (E5).

Cryogenic Dewar MLI & NER KPI (A=14.5 m², t=32 mm, 295 K -> 77.4 K, M=4,200 kg LN2)FormulaVerified Output
MLI Shell Heat Leak (W)((k_mW_mK / 1000) * Area * (Th - Tc)) / (t_mm / 1000)5.42 W intact (808.52 W soft vacuum)
Total Parasitic Heat Load (W)MLI_Shell_Leak_W + Piping_Support_Leak_W8.22 W (811.32 W icing outer shell)
Daily Cryogen Boil-Off (kg/d)(Total_Parasitic_W * 86.4) / Latent_hfg_kJ_kg3.57 kg/d (352.07 kg/d relief blow)
Normal Evaporation Rate NER (%/d)(Daily_BoilOff_kg_d / Stored_Mass_kg) * 1000.085%/d spec (8.383%/d vacuum loss)

MLI Apparent Fourier Conduction & Cryogenic Normal Evaporation Rate (NER) Formula

Validate Surface_Area A in [0.2, 2,000] m², MLI_Thickness t in [5, 150] mm, Apparent keff in [0.01, 35.0] mW/(m·K), Cryogen T_c in [1.8, 200] K, Ambient T_h >= T_c + 50 up to 360 K, Neck_Leak >= 0 W, Latent hfg in [20, 600] kJ/kg, and Stored_Mass > 0 kg.

=LET(ar_m, B2, tm_m, B3, km_w, B4, th_k, B5, tc_k, B6, qn_w, B7, hf_g, B8, ms_k, B9, qm_w, ((km_w / 1000) * ar_m * (th_k - tc_k)) / (tm_m / 1000), mb_d, ((qm_w + qn_w) * 86.4) / hf_g, IF(OR(ar_m < 0.2, ar_m > 2000, tm_m < 5, tm_m > 150, km_w < 0.01, km_w > 35, tc_k < 1.8, tc_k > 200, th_k < tc_k + 50, th_k > 360, qn_w < 0, hf_g < 20, hf_g > 600, ms_k <= 0), "Invalid Dewar Input", ROUND((mb_d / ms_k) * 100, 3)))

Saturated Getter / Weld Micro-Leak (k_eff = 8.2 mW/m·K Soft Vacuum) Frosting Check

Lose annular getter vacuum to ~0.1 mbar so gas conduction jumps keff to B4 = 8.20 mW/(m·K): Shell Heat Leak E2 explodes 149x to 808.52 W (811.32 W total in E3), boiling off 352.07 kg/day (8.383%/day NER in E5) while sweating frost bands across the carbon-steel outer jacket.

=IF(ISTEXT(E5), E5, LET(qm_w, ((B4 / 1000) * B2 * (B5 - B6)) / (B3 / 1000), ROUND(((qm_w + B7) * 86.4) / B8, 2)))

Try the example

Use the original values or change them to test your understanding.

Further reading