Sheet-Metal Stamping & Press-Shop Die Cushions, Siebel Blank-Holder Pressure & LDR Gate
Deep-Drawing LDR & Siebel Blank-Holder Cushion Formula
Calculate First-Draw Ratio Beta (D0 / dp), Siebel Anti-Wrinkling Blank-Holder Pressure pbh (MPa), Required Nitrogen/Pneumatic Die-Cushion Force (kN), and LDR Single-Stage Gate.
Too little blank-holder cushion pressure buckles cup flanges into radial wrinkles—too much or exceeding beta = 2.10 LDR rips the bottom right off the punch nose
Drawing a flat sheet-metal disc (Blank Diameter D_0 mm, Thickness t mm, Ultimate Tensile Strength UTS MPa) into a seamless cup over Punch Diameter d_p (mm with Die-Throat Clearance d_d ~= d_p + 2.5 * t) subjects the shrinking outer flange to intense circumferential hoop compression. Erich Siebel (1954) quantified the **Minimum Anti-Wrinkling Blank-Holder Contact Pressure pbh = k * ((beta - 1)^2 + (d_p / (200 * t))) * UTS (MPa, where Draw Ratio beta = D_0 / d_p and k ~= 0.0020–0.0030**), which acts across Initial Annular Binder Ring Area Abh = (pi / 4) * (D_0^2 - (d_p + 2.5 * t)^2) (mm²) to set **Die-Cushion Clamp Force Fbh = (pbh * Abh) / 1,000 (kN). Even with ideal binder lubrication, deep-drawing quality steels (DDQ, normal anisotropy r_m ~= 1.6–1.8) hit Limiting Draw Ratio LDR = betamax ~= 2.10—beyond which radial flange drawing force exceeds cup-wall tensile strength and tears the punch bottom clean off** unless split into a two-stage first draw + redraw.
Verify on a 100 mm Diameter Automotive Filter Housing Cup—Blank_Diameter D_0 = 195 mm (B2), Punch_Diameter d_p = 100 mm (B3), Sheet_Thickness t = 1.20 mm (B4), Steel_UTS = 360 MPa (B5), and Siebel_Constant k = 0.0025 (B6): First-Draw Ratio beta equals 1.95 (E2), Siebel Blank-Holder Pressure equals 1.187 MPa (E3), Required Die-Cushion Force equals 25.56 kN (2.61 tf, E4), passing "SINGLE-STAGE DRAW SAFE (<=2.10)" in E5.
| Siebel Cushion & LDR Gate KPI (dp=100 mm, t=1.2 mm, UTS=360 MPa, k=0.0025) | Formula | Verified Output |
|---|---|---|
| First-Stage Draw Ratio Beta | Blank_Diameter_D0_mm / Punch_Diameter_dp_mm | 1.95 (2.35 @ 235 mm oversize blank) |
| Siebel Holder Pressure pbh (MPa) | k * (((beta - 1) ^ 2) + (dp / (200 * t))) * UTS | 1.187 MPa (2.015 MPa flange friction) |
| Die-Cushion Clamp Force (kN) | (pbh * (PI/4) * (D0^2 - (dp + 2.5*t)^2)) / 1000 | 25.56 kN (70.62 kN cushion load) |
| Limiting Draw Ratio Gate | IF(beta <= 2.10, "SINGLE-STAGE...", "EXCEEDS LDR...") | SINGLE-STAGE DRAW SAFE (<=2.10) |
Erich Siebel (1954) Anti-Wrinkling Binder Pressure & 2.10 LDR Redraw Formula
Validate Punch_Diameter d_p in [10, 1,500] mm, Blank_Diameter D_0 in (1.05 * d_p, 3.50 * d_p], Sheet_Thickness t in [0.1, 15.0] mm, UTS in [80, 1,500] MPa, and Siebel_Factor k in [0.001, 0.006].
=LET(dz_m, B2, dp_m, B3, th_m, B4, ut_m, B5, sk_f, B6, IF(OR(dp_m < 10, dp_m > 1500, dz_m <= dp_m * 1.05, dz_m > dp_m * 3.5, th_m < 0.1, th_m > 15, ut_m < 80, ut_m > 1500, sk_f < 0.001, sk_f > 0.006), "Invalid Draw Input", ROUND(dz_m / dp_m, 2)))Taller Cup Blank (D_0 = 235 mm -> beta = 2.35 > 2.10) Bottom-Split Redraw Check
Enlarge the blank to B2 = 235 mm to form a deeper housing in one hit: Draw Ratio beta E2 climbs to 2.35, Cushion Force E4 nearly triples to 70.62 kN (2.015 MPa in E3), and E5 flags "EXCEEDS LDR — REDRAW REQUIRED" (use a 125 mm first draw @ beta1 = 1.88 followed by a 100 mm redraw @ beta2 = 1.25).
=IF(ISTEXT(E2), E2, LET(bt_r, B2 / B3, pb_m, B6 * (((bt_r - 1) ^ 2) + (B3 / (200 * B4))) * B5, ROUND((pb_m * (PI() / 4) * ((B2 ^ 2) - ((B3 + 2.5 * B4) ^ 2))) / 1000, 2)))Try the example
Use the original values or change them to test your understanding.