Fluid-Power Sealing, Parker / AS568 Elastomer O-Ring Glands, Squeeze & Extrusion
Elastomer O-Ring Squeeze % & Gland Fill Swell Formula
Calculate Linear Diametral Interference Squeeze (mm), Percentage Cross-Sectional Squeeze (%), Swollen-Elastomer Rectangular Gland Fill (%), and Parker Static Gland Compliance.
Rubber is incompressible (nu ≈ 0.499)—machining an O-ring groove to 100% fill hydraulic-locks the flange or shears the O-ring on hot oil swell
Novice CAD designers machine an O-ring groove JUST wide enough to fit the compressed circle (Area = (PI()/4) * CS^2)—forgetting two laws of elastomer physics: (1) Vulcanized FKM / NBR rubber is nearly as incompressible as hydraulic oil (Poisson’s ratio ≈ 0.4995), AND (2) rubber has 10x the thermal expansion coefficient of steel plus 5%–15% volumetric swell in hot hydrocarbon fluids. Under the Parker O-Ring Handbook / ISO 3601-2 static radial/face gland rules, Gland Depth h (mm) compresses Cord Cross-Section CS (mm, e.g. 3.53 mm for AS568 -2xx series) by Linear Squeeze CS - h to hit 15% <= Squeeze% <= 30% (((CS - h) / CS) * 100), WHILE Rectangular Groove Width w (mm) MUST keep **Swollen Gland Fill Fill% = (((PI()/4) * CS^2 * (1 + Swell%/100)) / (h * w)) * 100 <= 85%** (75% ideal) so the expanding elastomer has void breathing room without extruding into the clearance gap.
Verify on an AS568-224 (CS = 3.53 mm) FKM Static Hydraulic Flange Gland—O-Ring_Cord_Cross-Section CS = 3.53 mm (B2), Machined_Groove_Depth h = 2.75 mm (B3 -> Linear Squeeze = 0.78 mm in E2 & Squeeze = 22.10% in E3), Machined_Groove_Width w = 4.80 mm (B4), and Hot-Oil_Plus_Thermal_Volume_Swell = 12.0% (B5): Swollen Gland Fill equals 83.04% <= 85% (E4), passing "PARKER STATIC GLAND PASS" (E5).
| ISO 3601 / Parker O-Ring Gland KPI (CS=3.53 mm, Depth h=2.75 mm, Width w=4.80 mm, 12% Swell) | Formula | Verified Output |
|---|---|---|
| Diametral Compression Squeeze (mm) | Cord_CS_mm - Gland_Depth_h_mm | 0.78 mm |
| Cross-Sectional Squeeze (%) | ((CS_mm - h_mm) / CS_mm) * 100 | 22.10% (inside 15%–30% static window) |
| Swollen Gland Fill (%) | (((PI()/4)*CS^2*(1+Swell/100)) / (h*w))*100 | 83.04% (110.72% > 100% LOCK @ w=3.60 mm) |
| Parker Static Gland Design Gate | 15% <= Squeeze <= 30% AND Fill <= 85% | PARKER STATIC GLAND PASS |
ISO 3601-2 O-Ring Cross-Section Squeeze & Swollen Gland-Fill Formula
Validate 0 < Gland_Depth h < Cord_CS, Gland_Width w >= Cord_CS, and Volume_Swell in [0%, 50%] right on E2 (checking ISTEXT(E2) on E3..E4).
=LET(cs_m, B2, gh_m, B3, gw_m, B4, sw_p, B5, sq_p, ((cs_m - gh_m) / cs_m) * 100, ao_m, (PI() / 4) * (cs_m ^ 2) * (1 + sw_p / 100), fl_p, (ao_m / (gh_m * gw_m)) * 100, IF(OR(gh_m <= 0, cs_m <= gh_m, gw_m < cs_m, sw_p < 0, sw_p > 50), "Invalid O-Ring Gland", IF(AND(sq_p >= 15, sq_p <= 30, fl_p <= 85), "PARKER STATIC GLAND PASS", "EXTRUSION OR UNDER-SQUEEZE")))Cramped 3.60 mm Groove Width Hydraulic-Lock & Nibbling Extrusion Check (Set Groove Width B4 = 3.60 mm)
Narrow the machined groove width from 4.80 down to 3.60 mm (B4 = 3.6): Squeeze E3 stays 22.10%, yet Swollen Gland Fill E4 jumps to 110.72% (> 100% incompressible overflow), triggering "EXTRUSION OR UNDER-SQUEEZE" in E5 as expanding rubber shears into the mating gap.
=IF(ISTEXT(E2), E2, ROUND((((PI() / 4) * (B2 ^ 2) * (1 + B5 / 100)) / (B3 * B4)) * 100, 2))Try the example
Use the original values or change them to test your understanding.