Arte SheetsLearn. Try. Understand.

Foundry Sand Lab & Defect Control, AFS Standard 2-Inch Specimen Permeability Formula

Foundry Green-Sand AFS Permeability & Blowhole Formula

Calculate Volumetric Air Venting Rate (cm³/min), Superficial Darcy Gas Velocity (cm/min), AFS Permeability Number P, and Iron/Steel Castings Steam-Blowhole Gate.

Every gram of green-sand moisture flashes 1,600x in volume to steam at 1,420°C iron pour—and if dust fines choke AFS permeability below 50, trapped steam boils right back into the casting

When 1,400–1,580°C molten ductile iron or steel hits 3.2%-moisture bentonite-bonded Foundry Green Sand, interfacial water flashes explosively into superheated steam alongside sea-coal hydrocarbon and resin core gases. Under the American Foundry Society (AFS) Standard 2 x 2-Inch Cylindrical Rammed Specimen Test (Bell Air Volume V = 2,000 cm³, Specimen Height H = 5.08 cm, Cross-Sectional Area A = 20.268 cm², Water-Manometer Pressure Head p = 10.0 gf/cm² = 10 cm H_2O, and Measured Venting Time t minutes), Darcy Gas Conductivity defines the dimensionless-industrial **AFS Permeability Number P = (V * H) / (p * A * t)** (= 50.128 / (p * t) on standard 2" tooling). Gray/ductile iron high-pressure molding lines require P >= 80–120 (>= 50 absolute floor for medium iron/steel; 150–250 heavy steel)—let dead-clay oolitics and baghouse silt drag P down to 20.5 (t = 2.45 min) and cope surfaces riddle with subsurface pinholes, gas blowholes, and scabbing.

Verify in the Foundry Sand Lab Log—Bell_Air_Volume V = 2,000 cm³ (B2), Specimen_Height H = 5.08 cm (B3), Specimen_Area A = 20.268 cm² (B4), Manometer_Pressure p = 10.0 gf/cm² (B5), and Stop-Watch_Elapsed_Time t = 0.58 min (34.8 s, B6): Volumetric Air Flow equals 3,448.3 cm³/min (E2), Superficial Gas Velocity equals 170.1 cm/min (E3), AFS Permeability Number P equals 86.4 (E4), clearing "VENTING SAFE (>=50 AFS)" for ductile-iron pouring (E5).

AFS 2x2-in Sand Lab Permeability KPI (V=2,000 cm³, H=5.08 cm, A=20.268 cm², p=10 gf/cm²)FormulaVerified Output
Volumetric Air Flow (cm³/min)Bell_Air_Vol_cm3 / Vent_Time_min3,448.3 cm³/min (816.3 @ silt-choked sand)
Superficial Darcy Velocity (cm/min)(Bell_Air_Vol_cm3 / Time_min) / Area_cm2170.1 cm/min (40.3 cm/min choked)
AFS Permeability Number P(Vol_V * Height_H) / (Press_p * Area_A * Time_t)86.4 AFS (20.5 AFS over-rammed/silty)
Iron/Steel Gas-Venting GateIF(AFS_Perm >= 50, "VENTING SAFE...", "BLOWHOLE...")VENTING SAFE (>=50 AFS)

AFS Darcy Sand Permeability Number & Steam-Venting Defect Formula

Validate Air_Volume V in [500, 5,000] cm³, Specimen_Height H in [2.0, 10.0] cm, Specimen_Area A in [5.0, 50.0] cm², Manometer_Pressure p in [1.0, 50.0] gf/cm², and Elapsed_Time t in (0.05, 20.0] min.

=LET(va_c, B2, hs_c, B3, as_c, B4, pm_g, B5, te_m, B6, IF(OR(va_c < 500, va_c > 5000, hs_c < 2, hs_c > 10, as_c < 5, as_c > 50, pm_g < 1, pm_g > 50, te_m <= 0.05, te_m > 20), "Invalid AFS Input", ROUND(va_c / te_m, 1)))

Dead-Clay Fines Buildup + Over-Tempering (t = 2.45 min -> 20.5 AFS) Blowhole Defect Check

Skip new-silica dilution so dead-clay fines and excess temper water stretch 2,000 cm³ bell drop time to B6 = 2.45 min: AFS Permeability E4 plunges 4.2x down to 20.5 (40.3 cm/min velocity in E3), flipping E5 to "BLOWHOLE / PINHOLE RISK (<50)"—requiring fresh AFS GFN 55 silica makeup and mechanical cope vent pins.

=IF(ISTEXT(E2), E2, ROUND((B2 * B3) / (B5 * B4 * B6), 1))

Try the example

Use the original values or change them to test your understanding.

Further reading