Arte SheetsLearn. Try. Understand.

Metal Casting Gating Design, Bernoulli Mold Aspiration Prevention & Pouring Time

Foundry Tapered Sprue Choke & Aspiration Ratio Formula

Calculate Aspiration-Free Top Sprue Entry Area A1 = A2*SQRT(h2/h1) (mm²), Torricelli Choke Velocity (m/s), Volumetric Pouring Rate (cm³/s), and Mold Fill Time (s).

A straight-sided cylindrical downsprue pulls sub-atmospheric vacuum—sucking air and moisture right through permeable green sand into molten metal

As liquid metal accelerates downward from Pouring-Basin Depth h_1 (mm) through Total Metallostatic Head h_2 (mm) to the sprue base choke, continuity A_1 * v_1 = A_2 * v_2 causes stream cross-section to contract. If a foundry patternmaker cuts a straight-walled cylindrical downsprue (A_1 = A_2), Bernoulli’s equation forces static pressure inside the sprue below 1 atm—aspirating air, steam, and oxide dross through porous sand walls (pinhole porosity & slag inclusions). Setting gauge static pressure P_1 = P_2 = 0 everywhere along the free-falling stream (v_1 = SQRT(2*g*h_1) and v_2 = SQRT(2*g*h_2)) proves the sprue MUST taper downward with Top Entry Area A_1 = A_2 * SQRT(h_2 / h_1). At the bottom Choke Area A_2 (mm²) with nozzle friction C_d (~0.78–0.88), Choke Velocity is v_choke = C_d * SQRT(2 * g * (h_2 / 1,000)) (m/s), filling Casting + Riser Volume V_mold (cm³) in t_pour = V_mold / Q_cm3_s seconds.

Verify on a Bottom-Choked Aluminum Sand Mold—Pouring_Cup_Metal_Head h_1 = 65.0 mm (B2), Total_Sprue_Base_Head h_2 = 260.0 mm (h_2 / h_1 = 4.0, B3), Sprue_Base_Choke_Area A_2 = 320.0 mm² (B4 -> Required Tapered Top Area A_1 = 320 * SQRT(4) = 640.00 mm² in E2), Gating_Discharge_Coeff C_d = 0.82 (B5 -> Choke Velocity = 1.85 m/s in E3 & Flow = 592.6 cm³/s in E4), and Total_Poured_Volume V_mold = 4,800.0 cm³ (B6): Mold Fill Time equals 8.10 seconds (E5).

Foundry Gating Sprue KPI (h1=65 mm, h2=260 mm, Choke A2=320 mm², Cd=0.82, V=4,800 cm³)FormulaVerified Output
Aspiration-Free Top Area A1 (mm²)Choke_Area_A2 * SQRT(Total_h2 / Cup_h1)640.00 mm² (846.64 mm² @ tall 455 mm sprue)
Bernoulli Choke Velocity (m/s)Cd * SQRT(2 * 9.80665 * (h2_mm / 1000))1.85 m/s (2.45 m/s @ tall 455 mm sprue)
Volumetric Pouring Rate (cm³/s)(A2_mm2 / 100) * (Choke_Vel_m_s * 100)592.6 cm³/s (783.9 cm³/s @ 455 mm)
Total Mold Pouring Time (sec)Casting_Plus_Riser_cm3 / Flow_Rate_cm3_s8.10 s (6.12 s @ tall 455 mm sprue)

Zero-Aspiration Parabolic Sprue Taper & Torricelli Choke Fill-Time Formula

Validate Cup_Head h_1 > 10 mm, Total_Head h_2 > h_1, Choke_Area A_2 > 0 mm², Discharge_Coeff C_d in [0.40, 1.0], and Mold_Volume > 0 cm³.

=LET(hc_m, B2, ht_m, B3, ac_m, B4, cd_g, B5, vm_c, B6, IF(OR(hc_m <= 10, ht_m <= hc_m, ac_m <= 0, cd_g < 0.4, cd_g > 1, vm_c <= 0), "Invalid Sprue Input", LET(vc_s, cd_g * SQRT(2 * 9.80665 * (ht_m / 1000)), qf_c, ac_m * vc_s, ROUND(vm_c / qf_c, 2))))

Tall Cope Flask 455 mm Metallostatic Head Check (Set Total Head h2 B3 = 455.0 mm)

Pour a deeper cope flask raising h_2 B3 from 260.0 to 455.0 mm (h_2 / h_1 = 7.0): Required Top Entry Area A_1 E2 widens to 846.64 mm² (2.646x choke area to prevent vacuum aspiration), Choke Velocity E3 accelerates to 2.45 m/s, Flow Rate E4 reaches 783.9 cm³/s, and Pour Time E5 shortens to 6.12 s.

=IF(ISTEXT(E5), E5, ROUND(B4 * SQRT(B3 / B2), 2))

Try the example

Use the original values or change them to test your understanding.

Further reading