Arte SheetsLearn. Try. Understand.

Switch-Mode Power Magnetics, Gapped Ferrite Buck/Flyback Inductors & Reluctance

Gapped Ferrite Core Inductor Reluctance, AL & Isat Formula

Calculate Total Series Magnetic Reluctance R_tot (MA/Wb), Gapped Inductance Factor AL (nH/turn²), Winding Inductance L (uH), and Hard-Saturation Peak Current Isat (A).

Paradox of power magnetics: grinding a 0.8 mm air gap into a ferrite core LOWERS inductance—so the inductor can store 15x MORE DC energy without saturating

Ungapped MnZn power ferrite (mu_r ≈ 2,200, B_sat ≈ 0.38 T at 100 °C) has tiny Core Magnetic Reluctance R_core = l_e / (mu_0 * mu_r * A_e) (mu_0 = 4*PI()*10^-7 H/m)—so even half an amp of DC buck/flyback bias drives B = (N * I) / (A_e * R_core) past 0.38 T, collapsing permeability to air and blowing the MOSFET. Grinding a non-magnetic Air Gap l_g (mm, where mu_r,air = 1) adds Series Gap Reluctance R_gap = l_g / (mu_0 * A_e) that dominates R_tot = R_core + R_gap (>93% of magnetic energy (1/2)*B^2/mu_0 now resides safely inside the non-saturating air gap), stabilizing Inductance Factor A_L = 10^9 / R_tot (nH/turn²), Winding Inductance L = (N^2 * A_L) / 1,000 (uH), and boosting Peak Saturation Current I_sat = (B_sat * A_e * R_tot) / N (A) by an order of magnitude.

Verify on an ETD34 Gapped Buck/Flyback Choke—Effective_Core_Path l_e = 78.0 mm (B2), Ground_Center-Leg_Air_Gap l_g = 0.80 mm (B3), Effective_Cross-Section A_e = 120.0 mm² (B4), Ferrite_Relative_Permeability mu_r = 2,200 (B5), Copper_Turns N = 36 (B6), and 100 °C Ferrite_Saturation_Flux B_sat = 0.38 T (B7): Total Reluctance hits 5.540 MA/Wb (E2), Gapped A_L equals 180.50 nH/turn² (E3), Winding Inductance equals 233.92 uH (E4), and Hard Saturation Current reaches 7.02 A (E5).

SMPS Gapped Ferrite KPI (le=78 mm, lg=0.80 mm, Ae=120 mm², mur=2,200, N=36, Bsat=0.38 T)FormulaVerified Output
Total Reluctance R_tot (MA/Wb)(le_m/(mu0*mur*Ae_m2) + lg_m/(mu0*Ae_m2))/1e65.540 MA/Wb (0.368 @ ungapped 0.02 mm)
Gapped AL Value (nH/turn²)1,000,000,000 / R_tot_A_Wb180.50 nH/N² (2,719.28 @ ungapped)
Winding Inductance L (uH)((Turns_N ^ 2) * AL_nH) / 1000233.92 uH (3,524.19 uH @ ungapped)
Peak Saturation Current Isat (A)(Bsat_T * Ae_m2 * R_tot_A_Wb) / Turns_N7.02 A (0.47 A saturates instantly @ 0.02 mm)

Magnetic Circuit Series Reluctance, AL Factor & Bsat Saturation Current Formula

Validate Core_Path l_e > 5 mm, Air_Gap l_g >= 0 mm, Core_Area A_e > 5 mm², Relative_Perm mu_r >= 50, Turns N >= 1, and B_sat in (0.10, 2.20] T.

=LET(le_m, B2 / 1000, lg_m, B3 / 1000, ae_m, B4 * 0.000001, mr_p, B5, nt_c, B6, bs_t, B7, mz_p, 4 * PI() * 0.0000001, rt_w, (le_m / (mz_p * mr_p * ae_m)) + (lg_m / (mz_p * ae_m)), IF(OR(B2 <= 5, B3 < 0, B4 <= 5, mr_p < 50, nt_c < 1, bs_t <= 0.1, bs_t > 2.2), "Invalid Magnetics Input", ROUND((bs_t * ae_m * rt_w) / nt_c, 2)))

Ungapped Mating-Surface Residual 0.02 mm Saturation Trap Check (Set Air Gap lg B3 = 0.02 mm)

Omit the center-leg spacer leaving only 0.02 mm (20 um) mirror-lapped mating contact (B3 = 0.02): Reluctance E2 plunges 15x to 0.368 MA/Wb (A_L = 2,719.28 nH/N² in E3, L = 3,524.19 uH in E4), and Saturation Current E5 collapses from 7.02 A down to 0.47 A—saturating on the very first PWM switching pulse.

=IF(ISTEXT(E5), E5, LET(le_m, B2 / 1000, lg_m, B3 / 1000, ae_m, B4 * 0.000001, mz_p, 4 * PI() * 0.0000001, rt_w, (le_m / (mz_p * B5 * ae_m)) + (lg_m / (mz_p * ae_m)), ROUND(((B6 ^ 2) * (1000000000 / rt_w)) / 1000, 2)))

Try the example

Use the original values or change them to test your understanding.

Further reading