Arte SheetsLearn. Try. Understand.

Aggregate Sizing & Mineral Processing, VSMA Vibrating Screen G-Force & Bed Stratification

Vibrating Screen G-Force, Bed Depth & VSMA Ratio Formula

Calculate Peak-to-Peak Circular Stroke (mm), Centrifugal Vibrator Acceleration Kv (G), Discharge-End Oversize Bed Depth (mm), and VSMA Bed-to-Aperture Ratio (<= 4.0).

Flooding a 16 mm vibrating screen deck to an 8.5x bed-to-aperture ratio (136.5 mm thick) traps undersize fines on top so clean spec gravel rides straight to the oversize pile

Circular-Motion Inclined Vibrating Screens (Eccentric Counterweight Radius r mm -> **Peak-to-Peak Throw S = 2 * r mm at Shaft Speed N RPM) stratify crushed stone only inside a narrow mechanical window: Centrifugal Throw Index K_v = ((r / 1,000) * ((2 * pi * N) / 60)^2) / 9.80665 (G-units, kept inside 3.5–5.5 G so rock launches clear of wire mesh without cracking side-plates), while Discharge-End Oversize Bed Depth dbed = (((Qover / 60) / rho_b) / (W * v_m)) * 1,000 (mm across Effective Deck Width W m, Material Travel Speed v_m m/min, and Bulk Density rho_b t/m³) MUST satisfy the Vibrating Screen Manufacturers Association (VSMA) Rule dbed / a <= 4.0** (<= 3.0 for sticky damp 100 kg/m³ clay/sand). Exceed 4 * a (where a mm is square mesh opening) and near-size particles never percolate down to touch the screen cloth.

Verify on a 1.8 m (6-ft) Wide Secondary Aggregate Sizing Deck—Eccentric_Amplitude r = 4.50 mm (B2), Vibrator_Speed N = 920 RPM (B3), Effective_Deck_Width W = 1.80 m (B4), Oversize_Discharge_Tonnage Qover = 145 t/h (B5), Conveying_Speed v_m = 22.0 m/min (B6), Loose_Bulk_Density rho_b = 1.55 t/m³ (B7), and Wire_Mesh_Aperture a = 16.0 mm (B8): Peak-to-Peak Stroke equals 9.0 mm (E2), Centrifugal Acceleration K_v equals 4.26 G (E3), Discharge Lip Bed Depth equals 39.4 mm (E4), giving an ideal 2.46x Bed-to-Aperture Ratio (<= 4.0 VSMA limit. E5).

VSMA Inclined Screen KPI (r=4.5 mm, 920 RPM, W=1.8 m, a=16 mm mesh)FormulaVerified Output
Peak-to-Peak Throw Stroke (mm)2 * Eccentric_Radius_r_mm9.0 mm
Vibrator Acceleration Kv (G)((r / 1000) * ((2 * PI * RPM / 60) ^ 2)) / g4.26 G (3.5–5.5 G structural window)
Discharge Lip Bed Depth (mm)(((Oversize_t_hr / 60) / rho_b) / (W * v_m)) * 100039.4 mm (136.5 mm flooded deck)
VSMA Bed-to-Aperture RatioDischarge_Bed_Depth_mm / Mesh_Opening_a_mm2.46 PASS (8.53 > 4.0 FINES CARRYOVER)

VSMA Vibrating Screen Centrifugal G-Force & Discharge Bed-Depth Formula

Validate Eccentric_Radius r in [1.0, 12.0] mm, Vibrator_RPM in [500, 1,800], Deck_Width W in [0.6, 4.5] m, Oversize_Load in [5, 2,500] t/h, Travel_Speed v_m in [6, 45] m/min, Bulk_Density in [0.8, 3.2] t/m³, and Mesh_Aperture a in [1.0, 150] mm.

=LET(er_m, B2, nr_p, B3, dw_m, B4, qo_t, B5, vm_m, B6, rb_t, B7, ap_m, B8, bd_m, (((qo_t / 60) / rb_t) / (dw_m * vm_m)) * 1000, IF(OR(er_m < 1, er_m > 12, nr_p < 500, nr_p > 1800, dw_m < 0.6, dw_m > 4.5, qo_t < 5, qo_t > 2500, vm_m < 6, vm_m > 45, rb_t < 0.8, rb_t > 3.2, ap_m < 1, ap_m > 150), "Invalid Screen Input", ROUND(bd_m / ap_m, 2)))

Reversed Counter-Rotation + Surge Feed (Q_over = 320 t/h, v_m = 14 m/min) Deck-Flooding Check

Wire the drive motor backward into uphill counter-rotation (v_m slows to B6 = 14.0 m/min) during a B5 = 320 t/h primary surge: Discharge Bed Depth E4 swells 3.5x to 136.5 mm, blowing VSMA Ratio E5 to 8.53 (> 4.0)—blinding apertures and dumping saleable < 16 mm chips into the crusher recycle loop.

=IF(ISTEXT(E5), E5, ROUND((((B5 / 60) / B7) / (B4 * B6)) * 1000, 1))

Try the example

Use the original values or change them to test your understanding.

Further reading