Arte SheetsLearn. Try. Understand.

Gear & Spline Production Machining, Internal Pull-Broaching Pitch, RPT & Tonnage

Internal Pull-Broaching Engaged Teeth & Tonnage Formula

Calculate Simultaneous Engaged Broach Teeth Ze, Total Instantaneous Uncut Chip Cross-Section (mm²), Peak Hydraulic Pull Force (kN), and Machine Pull Tonnage (metric tf).

Pulling a 12.5-mm-pitch spline broach through a longer 95 mm gear hub engages 7.6 teeth at once—packing chip gullets solid and snapping a $9,500 M42 HSS broach shank

Internal Hydraulic Pull Broaching cuts 24-tooth involute gear hubs and keyways in a single 6-second stroke because every stepped cutting ring stands higher by Rise Per Tooth RPT (a_z mm/tooth, 0.04–0.09 mm roughing)—yet because chips CANNOT escape until each tooth exits the far face of Workpiece Bore Length L_w (mm), **Tooth Pitch p (mm, sized via p ~= 1.75 * sqrt(L_w)) MUST keep Simultaneous Engaged Teeth Z_e = L_w / p inside 3.0 <= Z_e <= 6.0 (< 2.5 chatters; > 6.5 overloads shank root area and packs spiral chips solid inside gullets). Multiplying Total Instantaneous Chip Area Achip = Z_e * bperim * RPT (mm² across Total Cut Perimeter bperim mm) by Specific Cutting Pressure k_c (MPa = N/mm²) gives Broaching Pull Force F_b = (Achip * k_c) / 1,000 (kN, or F_b / 9.80665 metric ton-force tf** against pull-head shank tensile rating).

Verify on a 10-Ton Vertical Spline Pull-Broaching Machine Cutting Alloy Steel (k_c = 2,420 MPa)—Hub_Length L_w = 56.0 mm (B2), Broach_Pitch p = 12.5 mm (B3), Summed_Spline_Cut_Perimeter bperim = 78.5 mm (B4), Roughing_Rise_Per_Tooth RPT = 0.065 mm (B5), and Specific_Cutting_Force k_c = 2,420 MPa (B6): Simultaneous Engaged Teeth Z_e equals 4.48 (ideal 3–6 window. E2), Active Chip Cross-Section equals 22.86 mm² (E3), Peak Pull Force equals 55.32 kN (E4), requiring 5.64 tf (56% of 10-tf press rating. E5).

Internal Pull-Broaching KPI (Pitch p=12.5 mm, Cut Perimeter=78.5 mm, kc=2,420 MPa)FormulaVerified Output
Simultaneous Engaged Teeth ZeWorkpiece_Bore_Lw_mm / Tooth_Pitch_p_mm4.48 IDEAL (7.60 > 6 GULLET JAM)
Total Active Chip Area (mm²)Engaged_Ze * Perimeter_mm * RPT_mm22.86 mm² (56.68 mm² heavy step)
Peak Broach Pull Force (kN)(Active_Chip_Area_mm2 * Specific_kc_MPa) / 100055.32 kN (137.16 kN shank overload)
Machine Pull Tonnage (tf)Broach_Pull_Force_kN / 9.806655.64 tf safe (13.99 tf > 10-tf STALL)

Internal Pull-Broaching Engaged Teeth, Chip Area & Hydraulic Tonnage Formula

Validate Bore_Length L_w in [5, 600] mm, Tooth_Pitch p in [2, 50] mm, Cut_Perimeter bperim in [2, 800] mm, Rise_Per_Tooth RPT in [0.005, 0.400] mm, and Specific_Force k_c in [400, 5,000] MPa.

=LET(lw_m, B2, pt_m, B3, pw_m, B4, rp_m, B5, kc_m, B6, fk_n, ((lw_m / pt_m) * pw_m * rp_m * kc_m) / 1000, IF(OR(lw_m < 5, lw_m > 600, pt_m < 2, pt_m > 50, pw_m < 2, pw_m > 800, rp_m < 0.005, rp_m > 0.4, kc_m < 400, kc_m > 5000), "Invalid Broach Input", ROUND(fk_n / 9.80665, 2)))

Stacked Double Gear Blanks (L_w = 95 mm) + Heavy 0.095 mm RPT Broach-Snap Check

Stack two hubs (B2 = 95.0 mm) on a coarse B5 = 0.095 mm/tooth broach without widening pitch: Engaged Teeth E2 climbs to 7.60, Active Chip Section E3 jumps 2.48x to 56.68 mm², and Pull Load E5 spikes to 13.99 tf (137.16 kN in E4)—stalling a 10-ton cylinder or snapping the pull-neck tang.

=IF(ISTEXT(E5), E5, ROUND(((B2 / B3) * B4 * B5 * B6) / 1000, 2))

Try the example

Use the original values or change them to test your understanding.

Further reading