Arte SheetsLearn. Try. Understand.

Pore-Pressure Detection & Well Control, Jordan-Shirley (1966) d & Corrected dc Exponent

Jordan-Shirley Drilling d-Exponent & dc Overpressure

Calculate Bit Penetration per Revolution (ft/rev), Jordan-Shirley Raw d-Exponent, Rehm-McClendon Mud-Weight Corrected dc-Exponent, and Normal Compaction Trend Ratio (%).

Cheering a sudden drilling break from 48 to 135 ft/h in deep shale misses a 0.902 dc-exponent reversal—warning you just drilled into an under-compacted overpressured gas zone

J.R. Jordan and O.J. Shirley (1966) normalized Bingham’s rock drillability equation (R / (60 * N) = (12 * W / (1,000 * D))^d in oilfield units: ROP R ft/h, Rotary Speed N RPM, Weight on Bit W klbf, Bit Diameter D in) into the dimensionless **Drilling d-Exponent d = log10(R / (60 * N)) / log10((12 * W) / (1,000 * D)) (both arguments < 1, so negative/negative yields positive 1.1–1.8 tightening steadily with normal shale compaction). W.A. Rehm and R. McClendon (1971) added Mud-Weight Normalization d_c = d * (MWnorm / MWact) (ppg / ppg): whenever the bit penetrates an disequilibrium-compaction overpressured shale seal, elevated pore pressure slashes chip-hold-down differential (ECD - P_p), making ROP jump and d_c veer sharply LEFT (< 75% of the Normal Compaction Trend dcn ~= 1.45)**—giving mud loggers early kick warning BEFORE formation gas enters the wellbore.

Build this Pore-Pressure Log Sheet in a cloud collaboration workbook—Drilling_ROP R = 48.0 ft/h (B2), Rotary_Speed N = 120 RPM (B3), Weight_on_Bit W = 28.0 klbf (B4), Bit_Diameter D = 8.50 in (B5), Normal_Pore_Gradient MWnorm = 8.65 ppg (B6), and Active_Mud_Weight MWact = 9.20 ppg (B7): Penetration per Revolution equals 0.00667 ft/rev (E2), Raw d-Exponent equals 1.551 (E3), Corrected d_c-Exponent equals 1.458 (E4 = 100.6% right on the 1.45 normal compaction trend in E5). Note: if your well-site engineering team inspects cloud workbooks through the scoped OAuth Arte Sheets ChatGPT 0.1.0 connector (currently In review / Not published; read_range returns <= 200 raw cells/formulas + base revision without recalculating, consuming 0 Arte AI credits under the 120 calls/min account burst limiter, whereas in-app Pro Assistant explanations use metered monthly Arte AI credits), always verify live recalculated d_c cells inside Arte Sheets before accepting mud-weight suggestions.

Jordan-Shirley / Rehm-McClendon KPI (120 RPM, 28 klbf on 8.5 in bit, MW_norm=8.65 ppg)FormulaVerified Output
Penetration per Revolution (ft/rev)ROP_ft_hr / (60 * Rotary_RPM)0.00667 ft/rev (0.01875 drilling break)
Raw Jordan-Shirley d-ExponentLOG10(R / (60 * N)) / LOG10((12 * W_klbf) / (1000 * D_in))1.551 (1.231 raw drop)
Corrected dc-ExponentRaw_d_Exp * (Normal_Grad_ppg / Active_Mud_ppg)1.458 NORMAL (0.902 OVERPRESSURE)
Normal Trend Ratio (% of 1.45)(Corrected_dc / 1.45) * 100100.6% on-trend (62.2% FLOW-CHECK NOW)

Jordan-Shirley (1966) d-Exponent & Rehm-McClendon (1971) dc Pore-Pressure Formula

Validate ROP in [1, 600] ft/h, RPM in [20, 400] (with R / (60 * N) < 0.5 ft/rev), WOB in [2, 95] klbf (with 12 * W / (1000 * D) < 0.8), Bit_Diameter in [3.5, 26] in, Normal_Pore_Grad in [8.0, 9.5] ppg, and Active_Mud_Weight in [8.0, 22.0] ppg.

=LET(rp_f, B2, nr_p, B3, wb_k, B4, db_i, B5, gn_p, B6, mw_p, B7, pr_v, rp_f / (60 * nr_p), wn_d, (12 * wb_k) / (1000 * db_i), dc_x, (LOG10(pr_v) / LOG10(wn_d)) * (gn_p / mw_p), IF(OR(rp_f < 1, rp_f > 600, nr_p < 20, nr_p > 400, pr_v >= 0.5, wb_k < 2, wb_k > 95, db_i < 3.5, db_i > 26, wn_d >= 0.8, gn_p < 8, gn_p > 9.5, mw_p < 8, mw_p > 22), "Invalid d-Exp Input", ROUND((dc_x / 1.45) * 100, 1)))

Transition-Zone Drilling Break (ROP = 135 ft/h at 11.8 ppg Mud) Kick-Warning Check

Drill into a deep geopressured shale transition where ROP jumps to B2 = 135 ft/h despite B7 = 11.8 ppg weighted mud: Raw d E3 slips to 1.231 and Corrected d_c E4 plunges left to 0.902 (62.2% of normal trend in E5)—commanding an immediate pumps-off flow check before connection swabbing pulls a gas kick.

=IF(ISTEXT(E5), E5, LET(dx_r, LOG10(B2 / (60 * B3)) / LOG10((12 * B4) / (1000 * B5)), ROUND(dx_r * (B6 / B7), 3)))

Try the example

Use the original values or change them to test your understanding.

Further reading