Arte SheetsLearn. Try. Understand.

Powder Metallurgy, Battery Cathode Calendering & Pharma Bulk Handling, Kawakita Model

Kawakita Powder Volume Reduction & Cohesiveness Formula

Calculate Kawakita Engineering Volume Strain C (%), Compressed Bed Volume V (mL), Reciprocal Yield/Cohesion Pressure 1/b (MPa), and Asymptotic Packing Realization (%).

Where Heckel shines at high punch pressures (>50 MPa), Kawakita’s hyperbolic law captures low-pressure fluffy powder rearrangement and soft granule crushing

Fluffy spray-dried pharmaceutical granules, NMC811 battery cathode powders, and cosmetic compacts undergo 30%–50% volume collapse at low pressures (1–40 MPa) where Heckel plots curve non-linearly. K. Kawakita & K.-H. Lüdde derived the exact hyperbolic Volume-Reduction Equation from Initial Loose Volume V_0 (mL): **C = (V_0 - V) / V_0 = (a * b * P) / (1 + b * P)** (linearized as P / C = P / a + 1 / (a * b)), governed by TWO physical constants: Asymptotic Maximum Volume Reduction a (0 < a < 1, equal to Initial Interparticle Bed Porosity / Carr’s Compressibility Fraction as P -> infinity) and Plasticity/Rearrangement Coefficient b (MPa⁻¹), whose reciprocal P_k = 1 / b (MPa) defines the pressure needed to achieve exact 50% of maximum possible volume reduction (C = a / 2).

Verify on a Spray-Dried Agglomerated Granule Bed—Initial_Loose_Fill_Volume V_0 = 120.0 mL (B2), Asymptotic_Compressibility a = 0.38 (38% max volume reduction, B3), Kawakita_Coefficient b = 0.22 MPa⁻¹ (B4 -> Half-Compaction Pressure P_k = 1 / b = 4.55 MPa in E4), and Pre-Compression_Pressure P = 25.0 MPa (B5): Engineering Volume Reduction C reaches 32.15% (E2), Compacted Bed Volume shrinks to 81.42 mL (E3), realizing 84.62% of ultimate densification a (E5).

Kawakita Powder Compaction KPI (V0=120 mL, a=0.38, P=25 MPa: Soft b=0.22 vs Hard b=0.06)FormulaVerified Output
Volume Reduction Degree C (%)((a * b * P) / (1 + b * P)) * 10032.15% (22.80% @ stiff granule b=0.06)
Compressed Powder Volume V (mL)Loose_V0_mL * (1 - C_fraction)81.42 mL (92.64 mL @ b=0.06)
Half-Reduction Pressure Pk = 1/b (MPa)1 / Kawakita_b_inv_MPa4.55 MPa (16.67 MPa hard ceramic agglomerate)
Realized Fraction of Max a (%)((b * P) / (1 + b * P)) * 10084.62% (60.00% @ b=0.06)

Kawakita-Lüdde Hyperbolic Powder Volume Strain & Pk = 1/b Formula

Validate Loose_Volume V_0 > 1 mL, Max_Compressibility a in (0.05, 0.85), Kawakita b > 0.005 MPa⁻¹, and Applied_Pressure P > 0 MPa.

=LET(vz_m, B2, am_x, B3, bk_i, B4, pa_m, B5, IF(OR(vz_m <= 1, am_x <= 0.05, am_x >= 0.85, bk_i <= 0.005, pa_m <= 0), "Invalid Kawakita Input", ROUND(((bk_i * pa_m) / (1 + bk_i * pa_m)) * 100, 2)))

Hard Calcined Ceramic Granules (b = 0.06 MPa⁻¹ -> Pk = 16.67 MPa) Springback Check (Set b B4 = 0.06)

Over-calcine spray-dried ceramic granules so granule crush strength quadruples (b drops to B4 = 0.06 MPa⁻¹, P_k = 1 / b = 16.67 MPa in E4): at 25 MPa, Volume Reduction E2 stalls at 22.80% (92.64 mL in E3, only 60.00% of a in E5)—leaving intact "blackberry" granule boundaries that survive sintering as strength-limiting macro-pores.

=IF(ISTEXT(E5), E5, LET(cf_r, (B3 * B4 * B5) / (1 + B4 * B5), ROUND(B2 * (1 - cf_r), 2)))

Try the example

Use the original values or change them to test your understanding.

Further reading