API 682 Rotating Equipment, Centrifugal Pump Mechanical Seals & Tribology PV Limits
Mechanical Shaft Seal Balance Ratio, PV & Heat Formula
Calculate Net Seal-Face Contact Pressure Pf (MPa), Mean Sliding Velocity v (m/s), Tribological PV Factor (MPa·m/s), and Seal-Chamber Flush Heat Generation (W).
Put an unbalanced mechanical seal (B > 1.0) into a 18-bar boiler feed pump and fluid closing force boils the lubrication film dry in seconds
API 682 rotary mechanical end-face seals ride on a sub-micron liquid film between a stationary carbon/SiC ring and a rotating SiC/WC mating ring of Contact Area A_f (mm²) and Mean Diameter d_m (mm). Hydraulic Balance Ratio B = A_closing / A_f (~0.68–0.78 on stepped-sleeve balanced seals vs 1.10–1.25 on cheap unbalanced seals) pitted against Fluid Film Pressure-Gradient Factor k (~0.50 for linear non-flashing liquid drop) plus Mechanical Spring Pressure P_sp (MPa) determines Net Mechanical Face Contact Pressure P_f = (B - k) * Delta_P + P_sp (MPa). Multiplying P_f by Mean Sliding Speed v = (PI() * (d_m / 1,000) * RPM) / 60 (m/s) yields the critical Tribological PV = P_f * v (MPa·m/s) and Frictional Flush Heat Load Q_seal = f * (P_f * 10^6) * (A_f * 10^-6) * v = f * P_f * A_f * v watts—sizing the API Plan 11 / Plan 23 seal-flush cooler.
Verify on an API 682 Balanced SiC-vs-Carbon Pump Seal—Hydraulic_Balance_Ratio B = 0.72 (B2), Film_Gradient_Factor k = 0.50 (B3), Seal_Chamber_Differential Delta_P = 1.80 MPa (18 bar, B4), Spring_Pressure P_sp = 0.18 MPa (B5 -> Net Face Contact P_f = 0.576 MPa in E2), Mean_Face_Diameter d_m = 58.0 mm (B6), Pump_Speed = 2,950 RPM (B7 -> Sliding Speed v = 8.96 m/s in E3), Seal_Face_Area A_f = 1,090.0 mm² (B8), and Mixed-Film_Friction f = 0.07 (B9): Face PV equals 5.16 MPa·m/s (E4), generating 393.7 W of face heat (E5).
| API 682 Mechanical Seal KPI (B=0.72, k=0.50, dP=1.80 MPa, dm=58 mm @ 2,950 RPM) | Formula | Verified Output |
|---|---|---|
| Net Face Contact Pressure Pf (MPa) | (Balance_B - Film_k) * dP_MPa + P_spring | 0.576 MPa (1.350 MPa @ unbalanced B=1.15) |
| Mean Face Sliding Speed v (m/s) | (PI() * (Mean_Diam_mm / 1000) * RPM) / 60 | 8.96 m/s |
| Tribological PV Factor (MPa·m/s) | Net_Contact_Pf_MPa * Sliding_Speed_m_s | 5.16 MPa·m/s (12.09 @ unbalanced B=1.15) |
| Frictional Face Heat Load (W) | Friction_f * Pf_MPa * Face_Area_mm2 * v | 393.7 W (922.8 W vaporizes film @ B=1.15) |
API 682 Seal Balance Ratio, Face PV & Flush Heat Generation Formula
Validate Balance_Ratio B in (0.55, 1.50] (B <= k would pop the seal faces open under pressure spikes), Film_Factor k in [0.3, 0.8], B > k, Delta_P >= 0 MPa, Spring_Pressure > 0 MPa, Mean_Diam > 10 mm, RPM > 0, Face_Area > 50 mm², and Friction f in (0.01, 0.30].
=LET(br_s, B2, kf_g, B3, dp_m, B4, ps_m, B5, dm_m, B6, nr_m, B7, af_m, B8, fr_c, B9, IF(OR(kf_g < 0.3, kf_g > 0.8, br_s <= kf_g, br_s > 1.5, dp_m < 0, ps_m <= 0, dm_m <= 10, nr_m <= 0, af_m <= 50, fr_c <= 0.01, fr_c > 0.3), "Invalid Seal Input", LET(pf_m, (br_s - kf_g) * dp_m + ps_m, vs_m, (PI() * (dm_m / 1000) * nr_m) / 60, ROUND(fr_c * pf_m * af_m * vs_m, 1))))Unbalanced Seal (B = 1.15) High-Pressure Film-Flashing Failure Check (Set Balance Ratio B2 = 1.15)
Install a low-pressure unbalanced seal (B B2 = 1.15) in the same 18-bar stuffing box: Net Face Pressure E2 more than doubles to 1.350 MPa, PV E4 surges to 12.09 MPa·m/s, and Face Heat Generation E5 jumps +134% to 922.8 W—flashing the liquid boundary layer into dry-running thermal shock cracks.
=IF(ISTEXT(E5), E5, LET(pf_m, (B2 - B3) * B4 + B5, vs_m, (PI() * (B6 / 1000) * B7) / 60, ROUND(pf_m * vs_m, 2)))Try the example
Use the original values or change them to test your understanding.