Arte SheetsLearn. Try. Understand.

Ground Improvement & Reclamation, Ménard Dynamic Compaction Energy & Depth

Ménard Dynamic Compaction Depth & Specific Energy Formula

Calculate Crane Drop-Tamper Impact Energy W*H (tonne·m & MJ), Ménard-Lukas Effective Densification Depth n*SQRT(W*H) (m), and Grid Applied Specific Energy (kJ/m²).

Doubling a crawler crane’s drop height does NOT double compaction depth—Rayleigh/compression wave attenuation scales strictly with SQRT(W * H)

Deep Dynamic Compaction (DDC) densifies loose hydraulic sand reclamation, rubble fills, and collapsible loess by free-falling a heavy steel Tamper of Mass W (10–35 tonnes) from Crane Boom Height H (15–30 m). Louis Ménard & R. G. Lukas (FHWA GEC-1) established that **Maximum Effective Improvement Depth Dmax = n * SQRT(W * H) (m, with W in tonnes and H in meters), where Empirical Soil Attenuation Factor n equals 0.50–0.60 in clean pervious sands/gravels vs 0.35–0.40 in semi-pervious silty fills (where transient pore-water pressure absorbs impact energy). Dropping N_d blows per crater on Square Print Spacing S (m) delivers Single-Blow Energy E_1 = (W * 9.80665 * H) / 1,000 (MJ) and Pass Applied Specific Energy Egrid = (N_d * W * 9.80665 * H) / S^2** (kJ/m², targeting 800–2,500 kJ/m² across primary + ironing passes).

Verify on a Port Container-Yard Hydraulic Sand Reclamation Pass—Steel_Tamper_Mass W = 18.0 tonnes (B2), Free-Fall_Drop_Height H = 22.0 m (B3 -> Nominal Drop Rating W * H = 396.0 tonne·m in E2 & 3.88 MJ/blow in E4), Clean-Sand_Factor n = 0.52 (B4), Drops_Per_Crater N_d = 8 (B5), and Primary_Grid_Spacing S = 6.0 m (B6): Effective Improvement Depth reaches 10.35 m (E3) and Primary-Pass Specific Energy delivers 863.0 kJ/m² (E5).

FHWA GEC-1 Dynamic Compaction KPI (W=18 t, H=22 m, Nd=8 Drops)FormulaVerified Output
Nominal Impact Rating W*H (t·m)Tamper_Mass_W_t * Drop_Height_H_m396.0 tonne·m
Effective Improvement Depth (m)Soil_Factor_n * SQRT(W_t * H_m)10.35 m (7.16 m in silty fill n=0.36)
Single-Drop Potential Energy (MJ)(W_t * 9.80665 * H_m) / 10003.88 MJ / blow
Grid Specific Energy (kJ/m²)(Drops_Nd * W_t * 9.80665 * H_m) / S_m^2863.0 kJ/m² (430.0 kJ/m² @ S=8.5 m)

Ménard-Lukas Root-Energy Depth & Crater-Grid Specific Energy Formula

Validate Tamper_Mass W in [2, 50] t, Drop_Height H in [3, 40] m, Soil_Factor n in [0.25, 0.70], Drops N_d >= 1, and Grid_Spacing S in [1.5, 15.0] m.

=LET(wt_t, B2, hd_m, B3, nf_s, B4, nd_c, B5, sp_m, B6, IF(OR(wt_t < 2, wt_t > 50, hd_m < 3, hd_m > 40, nf_s < 0.25, nf_s > 0.7, nd_c < 1, sp_m < 1.5, sp_m > 15), "Invalid DDC Schedule", ROUND((nd_c * wt_t * 9.80665 * hd_m) / (sp_m ^ 2), 1)))

Fines-Rich Silty Fill (n = 0.36) & Over-Wide 8.5 m Grid Under-Compaction Check

Encounter silty hydraulic fill (n B4 = 0.36) while stretching crater spacing to S B6 = 8.5 m: Improvement Depth E3 shrinks -31% to 7.16 m and Grid Energy E5 halves to 430.0 kJ/m²—leaving loose liquefiable pockets below 7 m unless wick drains and closer 6 m print grids are restored.

=IF(ISTEXT(E5), E5, ROUND(B4 * SQRT(B2 * B3), 2))

Try the example

Use the original values or change them to test your understanding.

Further reading