Arte SheetsLearn. Try. Understand.

High-Voltage Transmission & Substation Duct Banks, NEC 310.15(C) Neher-McGrath Ampacity

Neher-McGrath Underground Cable Ampacity Formula

Calculate AC Skin/Proximity Conductor Resistance Rac (mOhm/m), Available Conductor Thermal Headroom (K), Maximum Continuous Ampacity Imax (A), and Joule Heat Load (W/m).

Dry backfill soil doubling trench thermal resistivity Rca from 0.88 to 1.85 K·m/W slashes 90°C XLPE underground feeder ampacity by 37%

NEC Section 310.15(C) & IEC 60287 govern underground medium/high-voltage XLPE/EPR cable ratings via J. H. Neher & M. H. McGrath’s (1957) Thermal Ohm’s Law: every watt per meter of conductor I^2 * Rac Joule heat (where Rac = Rdc * (1 + Y_c) includes 50/60 Hz skin + proximity increment Y_c) plus Dielectric Loss Temperature Rise Delta_T_d (°C) must conduct radially across Effective Total Thermal Resistance Rca (K·m/W, summing insulation, duct air space, concrete encasement, earth burial depth, and mutual heating from adjacent circuits) without exceeding Maximum Insulation Rating T_c (90°C for XLPE/EPR) above Ambient Earth Temperature T_a (°C): **Imax = SQRT((T_c - (T_a + Delta_T_d)) / (Rac * Rca))** (Amps).

Verify on a 35 kV 500-kcmil (240 mm²) Copper XLPE Underground Feeder—Max_Conductor_Temp T_c = 90.0°C (B2), Moist_Earth_Ambient T_a = 25.0°C (B3), Dielectric_Temp_Rise Delta_T_d = 1.4°C (B4), 90°C DC_Resistance Rdc = 78.5 uOhm/m (B5), AC_Skin/Proximity_Factor Y_c = 0.06 (B6), and Fluidized-Thermal-Backfill Rca = 0.88 K·m/W (B7): Rac equals 0.0832 mOhm/m (83.21 uOhm/m, E2), Available Thermal Headroom equals 63.6°C (E3), Maximum Continuous Ampacity reaches 932.0 A (E4), dissipating 72.27 W/m into the duct bank (E5).

Neher-McGrath Cable Ampacity KPI (90°C XLPE, Rdc=78.5 uOhm/m, Yc=0.06, dTd=1.4°C)FormulaVerified Output
AC Conductor Resistance Rac (mOhm/m)(Rdc_uOhm_m / 1000) * (1 + Skin_Prox_Yc)0.0832 mOhm/m
Available Thermal Headroom (°C)Max_Tc_C - (Soil_Ta_C + Dielectric_dTd_C)63.6°C (53.6°C @ 35°C summer soil)
Max Continuous Ampacity Imax (A)SQRT(Headroom_C / ((Rac_mOhm_m/1000) * Rca))932.0 A (590.1 A = -36.7% @ dry soil)
Dissipated Conductor Heat (W/m)(Max_Ampacity_A ^ 2) * (Rac_mOhm_m / 1000)72.27 W/m (28.97 W/m thermal runaway cap)

NEC 310.15(C) / IEC 60287 Neher-McGrath Thermal-Circuit Ampacity Formula

Validate Conductor_Temp T_c in [60, 105]°C, Ambient_Soil T_a in [-10, 55]°C, Dielectric_Rise dTd >= 0°C with positive headroom T_c - (T_a + dTd) >= 5°C, Rdc > 5 uOhm/m, Skin/Proximity Y_c in [0, 1.0], and Thermal_Resistance Rca in [0.2, 5.0] K·m/W.

=LET(tc_c, B2, ta_c, B3, dt_d, B4, rd_u, B5, yc_f, B6, rc_a, B7, ra_o, (rd_u * 0.000001) * (1 + yc_f), dh_c, tc_c - (ta_c + dt_d), IF(OR(tc_c < 60, tc_c > 105, ta_c < -10, ta_c > 55, dt_d < 0, dh_c < 5, rd_u <= 5, yc_f < 0, yc_f > 1, rc_a < 0.2, rc_a > 5), "Invalid Ampacity Input", ROUND(dh_c / rc_a, 2)))

Moisture-Migration Dried Trench Soil (T_a = 35°C, R_ca = 1.85 K·m/W) Derating Check

Bake moisture out of un-engineered native sandy soil during a summer heatwave (T_a B3 = 35°C, Rca B7 = 1.85 K·m/W): Headroom E3 shrinks to 53.6°C, Allowed Heat Dissipation E5 drops 60% (72.27 -> 28.97 W/m), and Safe Ampacity E4 plunges -36.7% to 590.1 A—explaining underground XLPE splice blowouts during August peak load.

=IF(ISTEXT(E5), E5, LET(ra_o, (B5 * 0.000001) * (1 + B6), dh_c, B2 - (B3 + B4), ROUND(SQRT(dh_c / (ra_o * B7)), 1)))

Try the example

Use the original values or change them to test your understanding.

Further reading