Arte SheetsLearn. Try. Understand.

Bulk Metal Forming, Open-Die Upset Forging, Barreling Friction Hill & Press Tonnage

Open-Die Upset Forging Friction-Hill & Tonnage Formula

Calculate Compressive Logarithmic True Strain, Constant-Volume Upsetted Diameter Df (mm), Siebel Friction-Hill Shape Multiplier C_f, and Peak Forging Press Force (kN).

As a forged pancake gets thinner, radial platen friction builds a conical "friction hill" that pushes press tonnage far above Yf * Area

Compressing a cylindrical steel billet of initial diameter D_0 (mm) and height h_0 (mm) down to final pancake height h_f (mm) induces Logarithmic True Height Strain epsilon = LN(h_0 / h_f) while plastic incompressibility (A_0 * h_0 = A_f * h_f) expands Instantaneous Diameter to D_f = D_0 * SQRT(h_0 / h_f). Because metal must flow radially outward against top and bottom flat-die Coulomb friction mu, radial inward shear restraint creates barreling and an axisymmetric conical pressure peak ("Friction Hill") at the billet center. Erich Siebel integrated the slab equilibrium equation to obtain the Forging Shape Multiplier C_f = 1 + (2 * mu * (D_f / 2)) / (3 * h_f) = 1 + (mu * D_f) / (3 * h_f)—so Peak Forging Force is F = (Y_f * C_f * A_f) / 1,000 kN.

Verify on a Hot-Forged 4140 Gear-Blank Pancake—Initial_Billet D_0 = 90.0 mm (B2), Initial_Height h_0 = 135.0 mm (B3), Final_Forged_Height h_f = 54.0 mm (B4 -> True Strain epsilon = 0.916 in E2 & Final Diameter D_f = 142.30 mm in E3), Hot_Flow_Stress Y_f = 165.0 MPa (B5), and Graphite-Lubricated_Die_Friction mu = 0.24 (B6): Siebel Friction-Hill Factor equals 1.211 (E4), requiring 3,177.4 kN (324 metric tons) of hydraulic press force (E5).

Open-Die Upset Forging KPI (D0=90 mm, h0=135 -> hf=54 mm, Yf=165 MPa, mu=0.24)FormulaVerified Output
Compressive True Strain epsilonLN(Initial_h0_mm / Final_hf_mm)0.916
Upsetted Final Diameter Df (mm)D0_mm * SQRT(h0_mm / hf_mm)142.30 mm
Siebel Friction-Hill Factor Cf1 + (mu * Df_mm) / (3 * hf_mm)1.211 (1.395 @ dry unlubricated 0.45)
Peak Forging Press Force (kN)(Yf_MPa * Cf * ((PI()/4)*Df^2)) / 10003,177.4 kN (3,661.5 kN @ dry die)

Incompressible Area Expansion & Siebel Friction-Hill Upset Forging Formula

Validate D_0 > 0 mm, 0 < h_f < h_0 (check h_0 / D_0 <= 2.5 in practice so slender billets do not Euler-buckle before upsetting), Flow_Stress Y_f > 0 MPa, and Die_Friction mu in [0, 0.577] (von Mises sticking shear ceiling 1 / SQRT(3) ≈ 0.577).

=LET(dz_m, B2, hz_m, B3, hf_m, B4, yf_m, B5, mu_d, B6, IF(OR(dz_m <= 0, hf_m <= 0, hz_m <= hf_m, (hz_m / dz_m) > 3, yf_m <= 0, mu_d < 0, mu_d > 0.577), "Invalid Forging Input", LET(df_m, dz_m * SQRT(hz_m / hf_m), af_m, (PI() / 4) * (df_m ^ 2), cf_s, 1 + (mu_d * df_m) / (3 * hf_m), ROUND((yf_m * cf_s * af_m) / 1000, 1))))

Dry Scale-Covered Die Lubricant Breakdown Check (Set Friction mu B6 = 0.45)

Lose graphite die lubrication so hot oxide scale raises mu B6 from 0.24 to 0.45: Final Diameter E3 stays 142.30 mm, yet Siebel Friction-Hill Factor E4 climbs from 1.211 to 1.395, adding +484.1 kN (3,661.5 kN in E5) and severely barreling the billet perimeter.

=IF(ISTEXT(E5), E5, LET(df_m, B2 * SQRT(B3 / B4), ROUND(1 + (B6 * df_m) / (3 * B4), 3)))

Try the example

Use the original values or change them to test your understanding.

Further reading