Arte SheetsLearn. Try. Understand.

Polymer Processing & Battery Electrode Coating, Gaskell Two-Roll Calendering Nip

Polymer Two-Roll Calendering Gaskell Nip Force Formula

Calculate Post-Nip Exit Sheet Gauge 1.226*H0 (mm), Peak Hydrodynamic Nip Pressure (MPa), Gaskell Roll Separating Force (kN), and Two-Roll Viscous Drive Power (kW).

Set a calender nip gap to 0.60 mm and the PVC sheet exits 22.6% THICKER—while generating 188 tonnes of roll-bending separating force

Rigid/flexible PVC film, rubber conveyor belting, and dry-process battery electrode lines squeeze high-viscosity melt (mu Pa·s) between counter-rotating heated steel rolls of Radius R (m), Surface Speed U (m/s), Face Width W (m), and Minimum Nip Gap H_0 (mm, h_0 = H_0 / 1,000 m). R. E. Gaskell’s classic Lubrication-Approximation Calender Nip Theory (deep flood-fed bank where dimensionless leave-off coordinate lambda = 0.475) proves two critical shop-floor phenomena: (1) Conservation of mass from peak-pressure stagnation to zero-pressure detachment swells **Sheet Exit Gauge Hexit = (1 + lambda^2) * H_0 = 1.226 * H_0 (+22.6% thicker than H_0 even BEFORE viscoelastic die swell), AND (2) Peak Nip Pressure Pmax = (0.755 * mu * U * SQRT(R / h_0)) / h_0 (Pa) and Roll Separating Force Fsep = (1.22 * mu * U * R * W) / h_0 (N) explode inversely with h_0—bowing un-crowned steel rolls in the center ("oxbow" thick-center gauge defect) while consuming Two-Roll Viscous Power Pdrive = 2.18 * mu * U^2 * SQRT(R / h_0) * W** (W).

Verify on a 1.60 m Wide PVC Flooring Calender Nip—Apparent_Melt_Viscosity mu = 4,200 Pa·s (B2), Chilled-Iron_Roll_Radius R = 0.30 m (600 mm diameter, B3), Roll_Surface_Speed U = 0.45 m/s (B4), Minimum_Nip_Gap H_0 = 0.60 mm (B5), and Sheet_Width W = 1.60 m (B6): Sheet Exit Gauge equals 0.736 mm (E2), Peak Nip Pressure hits 53.18 MPa (E3), Roll Separating Force reaches 1,844.6 kN (188.1 tonnes-force requiring roll crossing or hydraulic roll-bending compensation. E4), and Viscous Nip Power equals 66.33 kW (E5).

Gaskell Calender Nip KPI (mu=4,200 Pa·s, R=0.30 m, U=0.45 m/s, W=1.60 m, H0=0.60 vs 0.35 mm)FormulaVerified Output
Post-Nip Sheet Gauge H_exit (mm)1.226 * Min_Nip_Gap_H0_mm0.736 mm (0.429 mm @ H0=0.35 mm)
Peak Nip Pressure P_max (MPa)(0.755 * mu * U * SQRT(R/h0)) / (h0 * 1e6)53.18 MPa (119.36 MPa @ H0=0.35 mm)
Roll Separating Force F_sep (kN)(1.22 * mu * U * R * W) / (h0 * 1000)1,844.6 kN (3,162.2 kN roll bow @ 0.35 mm)
Two-Roll Viscous Power (kW)(2.18 * mu * U^2 * SQRT(R/h0) * W) / 100066.33 kW (86.85 kW @ H0=0.35 mm)

Gaskell Flood-Fed Newtonian Calendering Pressure, Separating Load & Power Formula

Validate Viscosity mu > 10 Pa·s, Roll_Radius R > 0.05 m, Speed U > 0.01 m/s, Nip_Gap H_0 in (0.02, 20.0] mm, and Width W > 0.1 m.

=LET(mu_p, B2, rr_m, B3, us_m, B4, hz_m, B5 / 1000, wf_m, B6, IF(OR(mu_p <= 10, rr_m <= 0.05, us_m <= 0.01, B5 <= 0.02, B5 > 20, wf_m <= 0.1), "Invalid Calender Nip", ROUND((2.18 * mu_p * (us_m ^ 2) * SQRT(rr_m / hz_m) * wf_m) / 1000, 2)))

Thin-Gauge 0.35 mm Nip Closing h0^(-3/2) Pressure Spike Check (Set Nip Gap B5 = 0.35 mm)

Screw down the hydraulic nip cylinders from 0.60 to 0.35 mm (B5 = 0.35): Exit Gauge E2 thins to 0.429 mm, Peak Pressure E3 more than DOUBLES (h_0^{-1.5} scaling) to 119.36 MPa, and Separating Force E4 surges to 3,162.2 kN (322 tonnes)—requiring roll-crown adjustment so center thickness stays flat.

=IF(ISTEXT(E5), E5, LET(hz_m, B5 / 1000, ROUND((1.22 * B2 * B4 * B3 * B6) / (hz_m * 1000), 1)))

Try the example

Use the original values or change them to test your understanding.

Further reading