Arte SheetsLearn. Try. Understand.

Composites Manufacturing, Pultrusion Heated-Die Residence Time, Pull Force & Line Speed

Pultrusion Composite Die Residence Time & Pull Force Formula

Calculate Heated-Die Cure Residence Time (s), Net Fiber Cross-Section Area (mm²), Viscous-Gelation Die Wall Pull Force (kN), and Continuous Profile Mass Output (kg/h).

Crank pultrusion haul-off speed 80% too fast and the exothermic cure peak gets dragged OUTSIDE the chrome-plated steel die

Continuous FRP Composite Pultrusion pulls unidirectional E-glass or carbon fiber rovings (Fiber Volume Fraction V_f ≈ 0.55–0.68) saturated with thermoset vinyl-ester, polyester, or epoxy resin through a multi-zone heated steel die of Length Ldie (m), Cross-Sectional Area A_p (mm² -> **Net Fiber Area A_f = A_p * V_f mm²), and Wetted Perimeter Pdie (mm) at Haul-Off Speed v (m/min). Thermoset gelation and >=92% degree-of-cure conversion demand sufficient Heated-Die Residence Time tres = (Ldie / v) * 60 (s, typically 75–140 s)—pull faster and the exothermic peak shifts past the die exit, causing centerline delamination cracks and uncured styrene blisters. Meanwhile, hydraulic reciprocating grippers must overcome Die-Wall Shear Pull Force Fpull = (Pdie / 1,000) * Ldie * tauavg (kN, combining entrance viscous drag, bulk compaction pressure, and pre-shrinkage friction tauavg kPa) while producing Hourly Profile Throughput dot_m = (A_p * 10^{-6}) * (v * 60) * rho_c** (kg/h).

Verify on a 480 mm² Structural E-Glass / Vinyl-ESTER Channel Pultrusion Line—Heated_Die_Length Ldie = 1.20 m (B2), Gripper_Line_Speed v = 0.75 m/min (B3), Profile_Cross-Section A_p = 480 mm² (B4), Fiber_Volume_Fraction V_f = 0.62 (B5), Die_Cavity_Perimeter Pdie = 140 mm (B6), Mean_Die-Wall_Traction tauavg = 48.0 kPa (B7), and Cured_Composite_Density rho_c = 2,030 kg/m³ (B8): Die Residence Time holds 96.0 s (E2), Fiber Area equals 297.6 mm² (E3), Hydraulic Pull Force equals 8.06 kN (E4), and Line Output hits 43.85 kg/h (E5).

Pultrusion Line KPI (L=1.20 m, Ap=480 mm², Vf=0.62, P=140 mm, v=0.75 vs 1.35 m/min)FormulaVerified Output
Die Cure Residence Time (s)(Die_Length_m / Line_Speed_m_min) * 6096.0 s (53.3 s under-cured @ 1.35 m/min)
Net Fiber Cross-Section (mm²)Profile_Area_mm2 * Fiber_Vol_Fraction_Vf297.6 mm²
Hydraulic Gripper Pull Force (kN)(Perimeter_mm / 1000) * L_m * Shear_kPa8.06 kN
Continuous Mass Output (kg/h)(Area_mm2 * 1e-6) * (v * 60) * Density43.85 kg/h (78.93 kg/h @ 1.35 m/min)

Pultrusion Die Residence Time, Roving Fill Area, Wall Traction & Output Formula

Validate Die_Length Ldie > 0.3 m, Line_Speed v > 0.05 m/min, Area A_p > 10 mm², Fiber_Fraction V_f in [0.30, 0.80], Perimeter Pdie > 10 mm, Wall_Shear > 1 kPa, and Density in [1,100, 2,400] kg/m³.

=LET(ld_m, B2, vs_m, B3, ap_m, B4, vf_r, B5, pd_m, B6, tw_k, B7, rc_k, B8, IF(OR(ld_m <= 0.3, vs_m <= 0.05, ap_m <= 10, vf_r < 0.3, vf_r > 0.8, pd_m <= 10, tw_k <= 1, rc_k < 1100, rc_k > 2400), "Invalid Pultrusion Input", ROUND((ap_m * 0.000001) * (vs_m * 60) * rc_k, 2)))

Over-Sped 1.35 m/min Exotherm Blowout & Uncured Core Check (Set Line Speed B3 = 1.35 m/min)

Push haul-off speed to v B3 = 1.35 m/min without lengthening the 1.20 m die or adding RF preheating: Nominal Output E5 jumps to 78.93 kg/h, yet Die Residence Time E2 plunges to 53.3 s—pushing exothermic peak shrinkage outside the constrained die cavity and splitting thick web fillets.

=IF(ISTEXT(E5), E5, ROUND((B2 / B3) * 60, 1))

Try the example

Use the original values or change them to test your understanding.

Further reading