Arte SheetsLearn. Try. Understand.

Powertrain & Off-Highway Machine Elements, ISO 4156 / ANSI B92.1 Involute Spline

SAE / ISO 4156 Involute Spline Flank & Shear Formula

Calculate Total Pitch-Circle Tangential Force (kN), Load-Shared Tooth Flank Compressive Stress (MPa), Minor-Root Torsional Shear Stress (MPa), and % of 120 MPa Case-Hardened Limit.

Assuming all 24 involute spline teeth share torque 100% equally misses Dudley’s Km = 0.50–0.75 index-error factor—fretting short misaligned PTO couplings into red iron-oxide dust

ISO 4156 and ANSI B92.1 (30° Pressure-Angle) Involute Splined Shafts transmit 30%–50% more torque than straight-sided keys because self-centering 30° involute flanks pilot under load—yet real index spacing errors and angular shaft misalignment mean only Load-Distribution Factor K_m (0.75 fixed aligned grease-packed hub; 0.50 sliding/misaligned PTO sleeve) of the N teeth carry **Pitch-Circle Tangential Force F_t = (2,000 * T) / D (N at Torque T N·m and Pitch Diameter D mm). Checking Compressive Flank Bearing Stress sigma_b = F_t / (N * h * L_e * K_m) (MPa across Radial Tooth Contact Height h mm and Effective Hub Engagement L_e mm, kept <= 120 MPa on carburized 58–62 HRC splines or <= 30 MPa sliding) alongside Solid Minor-Root Torsional Shear tau_r = (16,000 * T) / (pi * Dre^3)** (MPa at Minor Diameter Dre mm) prevents both flank fretting wear and torsional twist-off.

Verify on a 24-Tooth, 45 mm Pitch-Diameter Carburized 8620 Axle Hub Spline—Peak_Torque T = 1,450 N·m (B2), Pitch_Diameter D = 45.0 mm (B3), External_Minor_Root Dre = 41.5 mm (B4), Tooth_Count N = 24 (B5), Radial_Contact_Height h = 1.65 mm (B6), Engaged_Length L_e = 38.0 mm (B7), and Aligned_Load_Sharing K_m = 0.75 (B8): Total Pitch Tangential Force equals 64.44 kN (E2), Flank Compressive Stress equals 57.10 MPa (E3), Minor-Root Shaft Shear equals 103.32 MPa (E4), utilizing 47.6% of the 120 MPa hardened flank ceiling (E5).

ISO 4156 / Dudley Involute Spline KPI (24 Teeth, D=45 mm, Dre=41.5 mm, h=1.65 mm)FormulaVerified Output
Pitch Tangential Force Ft (kN)((2000 * Torque_Nm) / Pitch_D_mm) / 100064.44 kN (117.78 kN shock torque)
Flank Bearing Stress sb (MPa)Ft_N / (Teeth_N * Height_h * Le * Km)57.10 MPa (270.38 MPa crushing)
Minor-Root Shaft Shear (MPa)(16000 * Torque_Nm) / (PI() * (Dre_mm ^ 3))103.32 MPa (188.83 MPa root twist)
% of 120 MPa Hardened Limit(Flank_Bearing_MPa / 120) * 10047.6% SAFE (225.3% FRETTING STRIP)

ISO 4156 / Dudley Involute Spline Flank Contact & Polar Root Shear Formula

Validate Torque T > 0 N·m, Pitch_Diameter D in [8, 500] mm, Minor_Root Dre in [0.60 * D, D), Teeth N in [6, 120], Contact_Height h in [0.3, 15.0] mm, Engaged_Length L_e in [5, 500] mm, and Sharing_Factor K_m in [0.25, 1.00].

=LET(tq_n, B2, dp_m, B3, dr_m, B4, nt_s, B5, hc_m, B6, le_m, B7, km_f, B8, sb_m, ((2000 * tq_n) / dp_m) / (nt_s * hc_m * le_m * km_f), IF(OR(tq_n <= 0, dp_m < 8, dp_m > 500, dr_m < 0.6 * dp_m, dr_m >= dp_m, nt_s < 6, nt_s > 120, hc_m < 0.3, hc_m > 15, le_m < 5, le_m > 500, km_f < 0.25, km_f > 1), "Invalid Spline Input", ROUND((sb_m / 120) * 100, 1)))

Half-Engaged Misaligned Sliding Sleeve (T = 2,650 N·m, L_e = 22 mm, K_m = 0.50) Strip Check

Fail to seat a snap ring so hub engagement slips back to B7 = 22.0 mm under angular misalignment (B8 = 0.50) during a B2 = 2,650 N·m driveline shock: While Minor-Root Shear E4 (188.83 MPa) still survives in alloy steel, Flank Bearing Stress E3 jumps 4.7x to 270.38 MPa (225.3% of limit in E5)—spalling carburized cases and stripping internal hub teeth smooth.

=IF(ISTEXT(E5), E5, ROUND(((2000 * B2) / B3) / (B5 * B6 * B7 * B8), 2))

Try the example

Use the original values or change them to test your understanding.

Further reading