Arte SheetsLearn. Try. Understand.

Heavy-Duty Vehicle Suspension, Semi-Elliptic Multi-Leaf Springs & Stiffness

Semi-Elliptic Multi-Leaf Spring Stress & Deflection Formula

Calculate Total Leaf Count n = nf + ng, Uniform-Strength Leaf Bending Stress (MPa), Central Camber Deflection (mm), and Suspension Spring Rate k (N/mm).

Why stepping leaf lengths into a diamond-equivalent stack cuts deflection factor from 3/8 to a hybrid (3*nf + 2*ng) denominator

Heavy-duty truck, trailer, and rail bogie Semi-Elliptic Leaf Springs support Total Central Axle Load 2F (kN -> Eye Reaction F = (2F * 1,000) / 2 N at each shackle pin separated by Span 2L mm, Cantilever Half-Span L = (2L) / 2 mm) using n_f Full-Length Master Leaves plus n_g Stepped Graduated Leaves (n = n_f + n_g, each of Width b mm and Thickness t mm). Without pre-nipping, full-length leaves behave as parallel rectangular cantilevers (factor = 3), whereas graduated leaves behave as a uniform-strength triangular cantilever (factor = 2). Combining both gives **Un-Nipped Bending Stress sigma_b = (6 * F * L) / (n * b * t^2) (MPa), Central Camber Deflection delta = (12 * F * L^3) / (E * b * t^3 * (3 * n_f + 2 * n_g))** (mm, E in MPa = E_GPa * 1,000), and **Vertical Suspension Spring Rate k = (2F * 1,000) / delta** (N/mm).

Verify on a 28.0 kN (2.85-tonne) Rear Truck Leaf-Spring Pack—Spring_Seat_Load 2F = 28.0 kN (F = 14,000 N per eye, B2), Eye-to-Eye_Span 2L = 1,200 mm (L = 600 mm, B3), Leaf_Width b = 75.0 mm (B4), Leaf_Thickness t = 11.0 mm (B5), Full-Length_Leaves n_f = 2 (B6), Graduated_Leaves n_g = 6 (B7 -> n = 8 leaves in E2), and 51CrV4 Spring-Steel Modulus E = 207 GPa (B8): Leaf Bending Stress hits 694.2 MPa (E3), Camber Deflection reaches 97.56 mm (E4), and Spring Rate equals 287.0 N/mm (E5).

SAE Leaf-Spring Pack KPI (2F=28 kN, 2L=1,200 mm, 75x11 mm, nf=2, ng=6, E=207 GPa)FormulaVerified Output
Total Leaf Count nFull_Leaves_nf + Graduated_Leaves_ng8 leaves (10 leaves @ ng=8 helper pack)
Leaf Bending Stress sigma_b (MPa)(6 * F_N * L_mm) / (n * b_mm * t_mm^2)694.2 MPa (555.4 MPa @ ng=8)
Central Camber Deflection (mm)(12 * F * L^3) / (E_MPa * b * t^3 * (3*nf+2*ng))97.56 mm (79.82 mm @ ng=8)
Vertical Spring Rate k (N/mm)(2F_kN * 1000) / Deflection_mm287.0 N/mm (350.8 N/mm @ ng=8)

Semi-Elliptic Full + Graduated Cantilever Equivalence Stress & Stiffness Formula

Validate Axle_Load 2F > 0 kN, Span 2L >= 300 mm, Leaf_Width b > 10 mm, Leaf_Thick t > 2 mm, Full_Leaves n_f >= 1, Graduated_Leaves n_g >= 1, and Modulus E > 50 GPa.

=LET(fe_n, (B2 * 1000) / 2, lh_m, B3 / 2, bw_m, B4, th_m, B5, nf_c, B6, ng_c, B7, em_p, B8 * 1000, df_m, (12 * fe_n * (lh_m ^ 3)) / (em_p * bw_m * (th_m ^ 3) * (3 * nf_c + 2 * ng_c)), IF(OR(B2 <= 0, B3 < 300, bw_m <= 10, th_m <= 2, nf_c < 1, ng_c < 1, B8 <= 50), "Invalid Leaf Spring", ROUND((B2 * 1000) / df_m, 1)))

Heavy-Haul +2 Graduated Leaves Upgrade Check (Set Graduated Leaves B7 = 8)

Add 2 graduated leaves to upgrade from an 8-leaf to a 10-leaf heavy-service pack (B7 = 8, E2 = 10): Bending Stress E3 drops -20% to 555.4 MPa (extending shot-peened fatigue life dramatically), Deflection E4 tightens to 79.82 mm, and Spring Rate E5 stiffens to 350.8 N/mm.

=IF(ISTEXT(E5), E5, ROUND((6 * ((B2 * 1000) / 2) * (B3 / 2)) / ((B6 + B7) * B4 * (B5 ^ 2)), 1))

Try the example

Use the original values or change them to test your understanding.

Further reading