Arte SheetsLearn. Try. Understand.

Sheet-Metal Stamping & Press-Brake Forming, Gardiner Elastic-Plastic Springback Law

Sheet-Metal Bending Elastic Springback & Overbend Formula

Calculate Gardiner Springback Factor Ks, Unloaded Inside Bend Radius Rf (mm), Required Press-Brake Overbend Angle (deg), and Elastic Springback Angle Recovery (deg).

Switch from mild steel to Grade 5 Ti-6Al-4V titanium on a 12 mm radius punch and press-brake springback explodes 12x from 1.4° to 16.4°

Every sheet-metal bend retains an elastic core straddling its neutral axis: the instant the press-brake ram retracts, elastic unloading relaxes curvature so Loaded Inside Radius R_i (mm) springs open to a larger Final Unloaded Radius R_f (mm) while Included Bend Angle theta_f (deg) opens back by Delta_theta degrees. F. J. Gardiner’s (1957, ASME) Canonical Cubic Springback Equation governs pure elastic-perfectly-plastic bending from dimensionless ratio **u = (R_i * sigma_y) / ((E * 1,000) * t) (across Sheet Thickness t mm, Yield Strength sigma_y MPa, and Young’s Modulus E GPa): K_s = (R_i + t/2) / (R_f + t/2) = 4 * u^3 - 3 * u + 1**. Because neutral-axis arc length (R + t/2) * theta is conserved during unloading, hitting Target Finished Bend Angle thetatarget (deg) requires Loaded Press-Brake Overbend Angle thetapunch = thetatarget / K_s (Springback Loss Delta_theta = thetapunch - thetatarget) and leaves Unloaded Inside Radius R_f = ((R_i + t/2) / K_s) - t/2 (mm).

Verify on a 2.0 mm HSLA 340-MPa Steel Bracket bent to 90.0°—Loaded_Inside_Radius R_i = 6.0 mm (B2), Sheet_Thickness t = 2.0 mm (B3), Yield_Strength sigma_y = 340 MPa (B4), Youngs_Modulus E = 205 GPa (B5), and Target_Bend_Angle = 90.0° (B6): Gardiner Factor K_s equals 0.9851 (E2), Unloaded Inside Radius grows slightly to 6.106 mm (E3), Required Ram Overbend equals 91.36° (E4), compensating 1.36° elastic springback (E5).

Gardiner Press-Brake Springback KPI (t=2.0 mm, Target=90.0°: HSLA Steel vs Ti-6Al-4V)FormulaVerified Output
Gardiner Springback Factor Ks4 * ((Ri*sy / (E*1000*t))^3) - 3*u + 10.9851 steel (0.8458 titanium)
Unloaded Inside Radius Rf (mm)((Loaded_Ri_mm + t_mm/2) / Ks) - t_mm/26.106 mm (12.0 -> 14.370 mm growth)
Required Punch Overbend (deg)Target_Bend_Angle_deg / Springback_Ks91.36° (106.41° deep V-die needed)
Elastic Springback Recovery (deg)Required_Overbend_deg - Target_Angle_deg1.36° steel (16.41° titanium)

Gardiner (1957) ASME Elastic-Core Cubic Springback Ratio Formula

Validate Inside_Radius R_i > 0.2 mm, Thickness t > 0.1 mm, Yield_Strength in [30, 2,200] MPa, Modulus E in [40, 420] GPa, plastic-yielding regime u = (R_i * sigma_y) / (E * 1,000 * t) < 0.45 (above u = 0.50 the sheet stays 100% elastic and springs completely flat), and Target_Angle in [5°, 175°].

=LET(ri_m, B2, ts_m, B3, sy_m, B4, em_g, B5, ta_d, B6, uv_r, (ri_m * sy_m) / ((em_g * 1000) * ts_m), ks_f, 4 * (uv_r ^ 3) - 3 * uv_r + 1, IF(OR(ri_m <= 0.2, ts_m <= 0.1, sy_m < 30, sy_m > 2200, em_g < 40, em_g > 420, uv_r >= 0.45, ta_d < 5, ta_d > 175), "Invalid Springback Input", ROUND((ta_d / ks_f) - ta_d, 2)))

Aerospace Ti-6Al-4V Titanium (R_i = 12 mm, sigma_y = 980 MPa, E = 114 GPa) 16.4° Springback Check

Form 2.0 mm Ti-6Al-4V (B4 = 980 MPa high yield + B5 = 114 GPa half-modulus of steel) over a generous B2 = 12.0 mm (6t) punch radius to prevent outer-fiber cracking: K_s E2 drops to 0.8458, Inside Radius E3 blooms +2.37 mm to 14.370 mm, and Springback E5 explodes 12x to 16.41°—demanding a 73.6° included (106.41° swept overbend in E4) acute V-die.

=IF(ISTEXT(E5), E5, LET(uv_r, (B2 * B4) / ((B5 * 1000) * B3), ks_f, 4 * (uv_r ^ 3) - 3 * uv_r + 1, ROUND(((B2 + B3 / 2) / ks_f) - (B3 / 2), 3)))

Try the example

Use the original values or change them to test your understanding.

Further reading