Arte SheetsLearn. Try. Understand.

Metallurgical Heat Treatment, Gear Gas/Vacuum Carburizing & Fick’s Second Law

Steel Gas Carburizing Harris Case-Depth & Time Formula

Calculate Arrhenius Carburizing Diffusion Factor KT (mm/sqrt(hr)), Required Furnace Soak Hours (t = (ECD/KT)²), Case Depth Achieved at 4 Hours (mm), and Total Cycle Minutes.

Doubling carburized gear case depth takes FOUR TIMES the furnace hours—unless austenite temperature is boosted

Interstitial carbon diffusion into low-carbon alloy gear steel (8620, 18CrNiMo7-6) held in endothermic or low-pressure acetylene austenite (870–980 °C) obeys Adolf Fick’s Second Law dC/dt = D * d²C/dx², whose complementary error-function solution scales strictly with the square root of time. F. E. Harris (1944) calibrated the universal shop-floor Arrhenius Case-Depth equation (converted to SI millimeters with T_K = T_C + 273.15): ECD_mm = K_T * SQRT(t_hr) where K_T = 802.6 * EXP(-8,588 / T_K) (mm / SQRT(hr)). Because t_hr = (ECD_mm / K_T)^2, doubling case depth from 0.60 mm to 1.20 mm at constant furnace temperature quadruples soak time 4x—whereas raising low-pressure vacuum carburizing temperature by just +30 °C exponentially accelerates K_T and cuts furnace hours nearly 30%.

Verify on an 8620 Pinion-Gear Endothermic Gas Carburizing Cycle—Furnace_Austenite_Temp T = 925.0 °C (1,198.15 K, B2 -> Harris Rate Factor K_T = 0.619 mm/√hr in E2) and Target_Case_Depth ECD = 1.20 mm (B3): Required Carburizing Time equals (1.20 / 0.619)^2 = 3.76 hours (E3 = 225.6 minutes in E5), while a standard 4.0-hour reference soak produces 1.24 mm case depth (E4).

Harris Fickian Carburizing KPI (925 °C Austenite, Target ECD = 1.20 mm)FormulaVerified Output
Arrhenius Factor KT (mm/√hr)802.6 * EXP(-8588 / (Temp_C + 273.15))0.619 mm/√hr (0.737 @ 955 °C vacuum)
Required Furnace Soak (hours)(Target_ECD_mm / KT_Factor) ^ 23.76 hr (2.65 hr = -29.5% @ 955 °C)
Reference 4-Hour Case Depth (mm)KT_Factor * SQRT(4)1.24 mm (1.47 mm @ 955 °C)
Required Carburizing Cycle (min)Required_Soak_Hours * 60225.6 min (158.9 min @ 955 °C)

Harris Arrhenius Root-Time Carburizing Case-Depth & Soak Duration Formula

Validate Austenite Carburizing Temp_C in [840, 1,050] °C (above Ac3 austenite transformation and below grain-coarsening incipient fusion) and Target_ECD in (0.05, 6.0] mm.

=LET(tc_c, B2, ec_m, B3, IF(OR(tc_c < 840, tc_c > 1050, ec_m <= 0.05, ec_m > 6), "Invalid Carburizing Input", LET(kt_f, 802.6 * EXP(-8588 / (tc_c + 273.15)), hr_s, (ec_m / kt_f) ^ 2, ROUND(hr_s * 60, 1))))

955 °C Low-Pressure Vacuum Carburizing Temperature Boost Check (Set Temp B2 = 955.0 °C)

Step furnace temperature up +30 °C to 955.0 °C (B2 = 955) in a micro-alloyed fine-grain gear steel: Arrhenius Factor K_T E2 jumps from 0.619 to 0.737 mm/√hr, slashing Required Furnace Time E3 from 3.76 hr down to 2.65 hr (158.9 min in E5—saving over 66 minutes per furnace load).

=IF(ISTEXT(E5), E5, LET(kt_f, 802.6 * EXP(-8588 / (B2 + 273.15)), ROUND((B3 / kt_f) ^ 2, 2)))

Try the example

Use the original values or change them to test your understanding.

Further reading