Precision Abrasive Machining, Surface/Creep-Feed Grinding & Malkin Grinding Burn
Surface Grinding Specific Energy, MRR & Burn Power Formula
Calculate Volumetric Grinding Removal Rate Qw (mm³/s), Specific Removal Rate Per Wheel Width Q'w (mm³/(mm·s)), Grinding Spindle Power (kW), and Workpiece Heat-Partition Burn Load (kW).
Abrasive grinding consumes 10x more specific energy per mm³ than milling—and 65%–80% of that heat flows straight into the steel
Unlike sharp positive-rake carbide milling (u ≈ 2–4 J/mm³, where >80% of cutting heat leaves harmlessly in thick steel chips), abrasive aluminum-oxide or CBN grinding grit has steep negative rake, plowing and sliding wear flats that drive Specific Grinding Energy u up to 30–70+ J/mm³. At Wheel Contact Width b_w (mm), Downfeed Depth of Cut a_e (mm), and Worktable Traverse Speed v_w (m/min -> v_w * 1,000 / 60 mm/s), Volumetric Removal Rate is Q_w = b_w * a_e * (v_w * 1,000 / 60) (mm³/s), Specific Removal Rate per mm of wheel width is Q'_w = Q_w / b_w (mm³/(mm·s)), Net Grinding Spindle Power is P_grind = (u * Q_w) / 1,000 (kW), and Stephen Malkin’s Heat Partition Ratio epsilon_w (~0.65–0.80 in shallow conventional steel grinding) conducts Q_work = epsilon_w * P_grind kW directly into the ground surface—risking white-layer untempered martensite ("grinding burn") and tensile residual cracks when wheel dressing is overdue.
Verify on a Hardened Bearing-Raceway Surface Grind—Wheel_Contact_Width b_w = 18.0 mm (B2), Downfeed a_e = 0.025 mm (B3), Table_Speed v_w = 16.0 m/min (B4 -> Q_w = 120.00 mm³/s in E2 & Q'_w = 6.67 mm³/(mm·s) in E3), Sharp-Dressed_Specific_Energy u = 42.0 J/mm³ (B5 -> Spindle Power = 5.040 kW in E4), and Workpiece_Heat_Partition epsilon_w = 0.72 (B6): Heat Conducted Into Steel equals 3.629 kW (E5).
| Malkin Surface Grinding KPI (bw=18 mm, ae=0.025 mm, vw=16 m/min, u=42 J/mm³) | Formula | Verified Output |
|---|---|---|
| Volumetric Removal Rate Qw (mm³/s) | bw_mm * ae_mm * ((vw_m_min * 1000) / 60) | 120.00 mm³/s |
| Specific Removal Q'w (mm³/mm·s) | ae_mm * ((vw_m_min * 1000) / 60) | 6.67 mm³/(mm·s) |
| Grinding Spindle Power (kW) | (Specific_Energy_J_mm3 * Qw_mm3_s) / 1000 | 5.040 kW (8.160 kW @ glazed dull wheel) |
| Workpiece Thermal Burn Flux (kW) | Spindle_Power_kW * Heat_Partition_eps_w | 3.629 kW (5.875 kW triggers temper burn) |
Specific Removal Rate Q'w, Grinding Power & Malkin Thermal Partition Formula
Validate Width b_w > 0 mm, Downfeed a_e > 0 mm, Table_Speed v_w > 0 m/min, Specific_Energy u >= 10 J/mm³ (always >= 13.8 J/mm³ adiabatic melting energy of iron in fine grinding), and Heat_Partition epsilon_w in (0, 1].
=LET(bw_m, B2, ae_m, B3, vw_m, B4, us_j, B5, ep_w, B6, IF(OR(bw_m <= 0, ae_m <= 0, vw_m <= 0, us_j < 10, ep_w <= 0, ep_w > 1), "Invalid Grinding Input", LET(qw_s, bw_m * ae_m * ((vw_m * 1000) / 60), pg_k, (us_j * qw_s) / 1000, ROUND(pg_k * ep_w, 3))))Glazed Undressed Wheel Wear-Flat Burn Spike Check (Set Specific Energy u B5 = 68.0 J/mm³)
Skip diamond wheel dressing until grit wear flats drive Specific Energy u B5 from 42.0 up to 68.0 J/mm³: Material Removal E2 stays 120.00 mm³/s, yet Spindle Power E4 jumps +61.9% to 8.160 kW and Workpiece Heat Input E5 surges to 5.875 kW—explaining why operators monitor spindle-load kW meters to trigger automatic diamond dressing before grinding burn ruins hardened gears.
=IF(ISTEXT(E5), E5, LET(qw_s, B2 * B3 * ((B4 * 1000) / 60), ROUND((B5 * qw_s) / 1000, 3)))Try the example
Use the original values or change them to test your understanding.