Arte SheetsLearn. Try. Understand.

Microelectronics Assembly & IC Interconnects, MIL-STD-883 Thermosonic Wire Bonding

Thermosonic Wire Bonding FAB & MIL-STD-883 Pull Formula

Calculate EFO Free-Air Ball Diameter (um), Bonded Mashed-Ball Diameter (um), Nominal Wire Breaking Force (gf), and Vector-Resolved Axial Wire Tension (gf).

Pulling a flat low-loop bond wire upward with a 9.2 gf hook actually stresses the gold neck past 24 gf—snapping good bonds via trigonometric amplification

Thermosonic Ball-Wedge Wire Bonding sparks an Electronic Flame-Off (EFO) plasma wand at the tip of 4N Gold or Pd-coated Copper wire of Diameter d (um, 25.4 um = 1.0 mil) to form a spherical **Free-Air Ball DFAB ≈ 2.1 * d (um), then scrubs 120 kHz ultrasonic energy on a 175 °C aluminum die pad to mash a Bonded Ball Diameter Dmash ≈ 2.8 * d (um)—compared against Intrinsic Wire Tensile Strength FUTS = UTSMPa * ((PI() / 4) * (d / 1,000)^2) * (1,000 / 9.80665) (grams-force gf). During MIL-STD-883 Method 2011 Destructive Wire-Pull QC, a micro-hook lifts the loop apex with Vertical Gauge Reading Fhook (gf) at Die-Side Slope theta_1 and Lead-Side Slope theta_2 (deg). Static pulley equilibrium resolves True Axial Wire Tension Twire = Fhook / (SIN(theta_1) + SIN(theta_2))** (gf)—proving that shallow ultra-thin package loops (theta < 15°) record artificially low gauge readings even when the wire neck hits 100% UTS.

Verify on a 25.4 um (1.0-mil) Annealed 4N Gold Wire Bond—Wire_Diameter d = 25.4 um (B2 -> DFAB = 53.3 um in E2 & Dmash = 71.1 um in E3), Wire_Tensile_Strength UTS = 240 MPa (B3 -> Breaking Load = 12.40 gf in E4), Hook_Gauge_Pull Fhook = 9.20 gf (B4, far above the 3.0 gf MIL-STD-883 minimum), Ball_Leg_Angle theta_1 = 32.0° (B5), and Stitch_Leg_Angle theta_2 = 24.0° (B6): Resolved Axial Wire Tension equals 9.82 gf (79% of wire UTS, E5).

MIL-STD-883 Method 2011 Wire-Bond KPI (d=25.4 um, UTS=240 MPa, Hook=9.20 gf)FormulaVerified Output
EFO Free-Air Ball DFAB (um)2.1 * Wire_Diameter_d_um53.3 um
Bonded Mashed Ball Dmash (um)2.8 * Wire_Diameter_d_um71.1 um (fits >= 80 um bond-pad pitch)
Intrinsic Wire Breaking Load (gf)UTS_MPa * ((PI()/4)*(d/1000)^2)*(1000/9.80665)12.40 gf
Resolved Axial Wire Tension (gf)Hook_Pull_gf / (SIN(th1_rad) + SIN(th2_rad))9.82 gf (24.11 gf > UTS @ flat 12°/10° loop)

Wire-Bond Ball Geometry & MIL-STD-883 Trigonometric Hook-Pull Resolution Formula

Validate Wire_Diam d in [12, 500] um, UTS in [100, 1,200] MPa, Hook_Pull > 0.2 gf, and loop leg angles theta_1, theta_2 in [5°, 75°].

=LET(dw_u, B2, ut_m, B3, fh_g, B4, t1_r, B5 * (PI() / 180), t2_r, B6 * (PI() / 180), IF(OR(dw_u < 12, dw_u > 500, ut_m < 100, ut_m > 1200, fh_g <= 0.2, B5 < 5, B5 > 75, B6 < 5, B6 > 75), "Invalid Wire-Bond Input", ROUND(fh_g / (SIN(t1_r) + SIN(t2_r)), 2)))

Ultra-Low QFN Loop Profile (theta1 = 12°, theta2 = 10°) Trigonometric Neck-Snap Check

Flatten loop height on an ultra-thin QFN (theta_1 B5 = 12°, theta_2 B6 = 10°): 1 / (SIN(12°) + SIN(10°)) = 2.62x magnifies 9.20 gf hook force to 24.11 gf in E5 (nearly 2x the 12.40 gf wire breaking load—meaning the wire actually snaps at just 4.7 gf on the pull tester)—explaining why low-loop packages use Ball-Shear Testing (JESD22-B116) alongside wire pull.

=IF(ISTEXT(E5), E5, ROUND((B3 * (PI() / 4) * ((B2 / 1000) ^ 2)) * (1000 / 9.80665), 2))

Try the example

Use the original values or change them to test your understanding.

Further reading