Arte SheetsLearn. Try. Understand.

High-Precision Cylindrical Finishing, Centerless Grinding Regulating Feed & Lobing Geometry

Centerless Grinding Through-Feed & Workrest Angle Formula

Calculate Regulating-Wheel Surface Speed (m/min), Axial Through-Feed Rate (mm/min and m/min), and Above-Center Tangency Rounding Angle Beta (deg).

Setting a centerless grinder workrest blade right on wheel centerline (beta = 0.29°) copies every incoming bump into a constant-width Reuleaux 3-lobe triangle

Through-Feed Centerless Grinding finishes automotive piston pins, hydraulic spool valves, and bearing needles to < 0.5 um roundness without spindle centers by trapping Workpiece Diameter d_w (mm) between a fast Grinding Wheel (D_g mm), an angled carbide Workrest Blade, and a rubber-bonded Regulating Wheel (Diameter D_r mm, Speed N_r RPM) tilted by Feed Inclination Angle alpha (1°–6°). Resolving **Regulating Peripheral Velocity v_r = (pi * D_r * N_r) / 1,000 (m/min) along the workpiece axis fixes Axial Through-Feed Rate v_f = pi * D_r * N_r * sin(alpha) (mm/min). Crucially, elevating the workpiece center by Above-Center Height h_w (mm above the wheel-centerline chord) creates Tangency Rounding Angle beta = arcsin(h_w / ((D_g + d_w) / 2)) + arcsin(h_w / ((D_r + d_w) / 2)) (degrees, ideally 6°–8°): grind on-center (beta ~= 0°) and a high spot touching the regulating wheel pushes the opposite side straight into the grinding wheel—generating 3-lobe or 5-lobe odd-harmonic out-of-roundness** that fools two-point micrometers.

Verify on a 24 mm Hardened Wrist-Pin Through-Feed Setup—Regulating_Wheel_Diameter D_r = 300 mm (B2), Regulating_Speed N_r = 32.0 RPM (B3), Tilt_Angle alpha = 3.50° (B4), Grinding_Wheel_Diameter D_g = 500 mm (B5), Workpiece_Diameter d_w = 24.0 mm (B6), and Above-Center_Height h_w = 11.0 mm (B7): Regulating Surface Speed equals 30.16 m/min (E2), Axial Through-Feed Rate equals 1,841.2 mm/min (1.841 m/min in E4), and Tangency Rounding Angle beta sits right in the sweet spot at 6.30° (6°–8° odd-lobe suppression window. E5).

Centerless Grinding Kinematics KPI (Dr=300 mm @ 32 RPM, Dg=500 mm, dw=24 mm)FormulaVerified Output
Regulating Surface Speed (m/min)(PI() * Dr_mm * Nr_RPM) / 100030.16 m/min
Axial Through-Feed Rate (mm/min)PI() * Dr_mm * Nr_RPM * SIN(alpha_rad)1,841.2 mm/min (3,152.5 @ 6° tilt)
Axial Through-Feed Rate (m/min)Through_Feed_mm_min / 10001.841 m/min (3.153 m/min)
Tangency Rounding Angle Beta (deg)DEGREES(ASIN(2*hw/(Dg+dw)) + ASIN(2*hw/(Dr+dw)))6.30° IDEAL (0.29° 3-LOBE POLYGON)

Centerless Regulating-Wheel Helix Feed & Dall/Rowe Rounding-Angle Formula

Validate Regulating_Diameter D_r in [100, 600] mm, Regulating_RPM in [5, 300], Tilt_Angle alpha in [0.5, 10.0]°, Grinding_Diameter D_g in [200, 800] mm, Work_Diameter d_w in [1, 200] mm, and Above-Center Height h_w in [0, 0.25 * (D_r + d_w)] mm.

=LET(dr_m, B2, nr_p, B3, al_d, B4, dg_m, B5, dw_m, B6, hw_m, B7, IF(OR(dr_m < 100, dr_m > 600, nr_p < 5, nr_p > 300, al_d < 0.5, al_d > 10, dg_m < 200, dg_m > 800, dw_m < 1, dw_m > 200, hw_m < 0, hw_m > 0.25 * (dr_m + dw_m)), "Invalid Centerless Input", ROUND(((ASIN(hw_m / ((dg_m + dw_m) / 2)) + ASIN(hw_m / ((dr_m + dw_m) / 2))) * 180) / PI(), 2)))

Dropped Workrest Blade (h_w = 0.5 mm) + Steep 6° Feed 3-Lobe Out-of-Roundness Check

Forget to shim the workrest blade after wheel dressing (h_w drops to B7 = 0.50 mm) while steepening tilt to B4 = 6.0°: Axial Feed E3 rushes at 3,152.5 mm/min (3.153 m/min in E4), while Tangency Angle beta E5 collapses to 0.29°—guaranteeing 3-lobed Reuleaux pins that pass 2-point snap gauges yet seize inside cylindrical bores.

=IF(ISTEXT(E5), E5, ROUND(PI() * B2 * B3 * SIN((B4 * PI()) / 180), 1))

Try the example

Use the original values or change them to test your understanding.

Further reading