Mechanical Power Transmission, V-Belt Sheave Drives, Pitch Length & Wrap Angle
V-Belt Sheave Pitch Length & Small-Pulley Wrap Formula
Calculate Open-Drive V-Belt Pitch Length Lp (mm), Small-Sheave Arc of Contact Wrap Angle (deg), Speed Reduction Ratio (D/d), and Linear Belt Velocity (m/s).
Shorten a V-belt motor mount to save floor space and small-sheave wrap drops below 150°—slashing kW belt capacity by 12%–20%
When coupling an induction motor Small Sheave d (mm) to a fan, crusher, or compressor Large Sheave D (mm) across Shaft Center Distance C (mm), two geometric effects happen simultaneously that naive 2*C + PI()*(D+d)/2 estimates miss: (1) Diagonal belt spans add quadratic Pitman/Rankine slack term **((D - d)^2) / (4 * C) to Exact Open-Belt Pitch Length L_p = 2 * C + (PI() / 2) * (D + d) + ((D - d)^2) / (4 * C) (mm), AND (2) pulley diameter asymmetry steals wrap angle from the motor pulley, reducing Small-Sheave Arc of Contact theta_1 = 180° - 2 * ASIN((D - d) / (2 * C)) * (180 / PI()). Under RMA / ISO 4184 V-belt rating tables (180° wrap = C_theta = 1.00), letting theta_1 fall to 140° derates power transmission (C_theta ≈ 0.89) and invites belt squeal and glazed sidewalls—while Linear Belt Speed v = (PI() * (d / 1,000) * RPM) / 60** must stay below 30–33 m/s (~6,000–6,500 fpm) to avoid centrifugal tension throw-off on cast-iron sheaves.
Verify on a 1,750 RPM Industrial Blower V-Belt Drive—Driven_Large_Sheave D = 315.0 mm (B2), Motor_Small_Sheave d = 125.0 mm (B3 -> Speed Ratio = 2.52 in E4), Slide-Base_Center_Distance C = 520.0 mm (B4), and Motor_Speed = 1,750 RPM (B5): Belt Pitch Length equals 1,748.5 mm (E2), Small-Sheave Wrap Angle holds 158.95° (C_theta ≈ 0.95 in E3), and Linear Belt Speed runs cleanly at 11.45 m/s (E5). In a shared plant-maintenance workbook, a millwright with suggester access can propose a tighter slide-base center distance while an engineering owner or editor checks theta_1 before accepting the cell suggestion.
| ISO 4184 V-Belt Drive KPI (D=315 mm, d=125 mm, C=520 mm, 1,750 RPM) | Formula | Verified Output |
|---|---|---|
| V-Belt Pitch Length Lp (mm) | 2*C + (PI()/2)*(D+d) + ((D-d)^2)/(4*C) | 1,748.5 mm (1,283.4 mm @ short C=280 mm) |
| Small-Sheave Wrap Angle (deg) | 180 - 2 * ASIN((D-d)/(2*C)) * (180/PI()) | 158.95° (140.33° slip risk @ C=280 mm) |
| Speed Reduction Ratio (D / d) | Large_Sheave_D_mm / Small_Sheave_d_mm | 2.52 (:1) |
| Linear Belt Speed v (m/s) | (PI() * (d_mm / 1000) * Motor_RPM) / 60 | 11.45 m/s (well below 30 m/s iron limit) |
Open-Drive V-Belt Pitch Length, Small-Pulley Arc of Contact & Rim Speed Formula
Validate Small_Sheave d > 20 mm, Large_Sheave D >= d, non-touching sheaves Center_Distance C > (D + d) / 2, and Motor_RPM > 0. Try building the arc-of-contact ASIN conversion from radians to degrees first; if your wrap angle looks near 179°, ask the in-app AI assistant for a hint on scaling ASIN(...) by 180 / PI() rather than pasting a blind answer.
=LET(dl_m, B2, ds_m, B3, cd_m, B4, nr_m, B5, vs_m, (PI() * (ds_m / 1000) * nr_m) / 60, IF(OR(ds_m <= 20, dl_m < ds_m, cd_m <= (dl_m + ds_m) / 2, nr_m <= 0), "Invalid Sheave Drive", ROUND(vs_m, 2)))Cramped Skid 280 mm Center-Distance Wrap-Loss Check (Set Center Distance B4 = 280 mm)
Slide the motor base inward to C B4 = 280 mm (< D = 315 mm rule-of-thumb minimum): Pitch Length E2 drops to 1,283.4 mm and Small-Sheave Wrap Angle E3 plunges from 158.95° down to 140.33°—requiring an extra belt groove or grooved backside idler to prevent startup slip.
=IF(ISTEXT(E5), E5, ROUND(180 - 2 * (ASIN((B2 - B3) / (2 * B4)) * (180 / PI())), 2))Try the example
Use the original values or change them to test your understanding.